How to fix on-board battery charger if it will not operate on Tennant Scrubber?
If the on-board battery charger of your Tennant Scrubber isn't working, first check the plug connection to the power supply. If the connection is good, the charger fuse may be faulty, so replace it. Another potential cause is a faulty power supply cord, which would also need to be replaced.
What to do if Tennant Scrubber machine will not propel?
If your Tennant Scrubber won't propel, first check that the parking brake is released. If it is, a blown propel motor fuse could be the issue, so replace the 30A fuse. Another cause may be that the machine fault was detected, in this case consult Battery Meter LED Fault Codes. Finally, avoid steep inclines and reset the key if you've exceeded the maximum incline.
How to fix little or no solution flow in Tennant Scrubber?
If your Tennant Scrubber has little or no solution flow, the first thing to check is whether the solution tank is empty; if so, fill it. A clogged solution tank filter can also cause this issue, so clean the filter. Discharged batteries may be the reason, so charge them. Additionally, a clogged solution valve might be the problem; remove the valve and clean it. Make sure that the solution flow control knob is properly adjusted, and calibrate the knob and retighten the screw if it is loose.
How to fix a blinking red ec--H2O system indicator light on a Tennant T5E Floor Machine?
If the ec--H2O system indicator light is blinking red on your Tennant Floor Machine, it's likely due to mineral deposit build-up in the module. To resolve this, flush the module according to the ec--H2O MODULE FLUSH PROCEDURE.
What to do if my Tennant T5E Floor Machine will not operate?
If your Tennant Floor Machine isn't starting, several factors could be at play. First, ensure the batteries are fully charged. If the emergency-stop button is activated, turn it clockwise to reset it. Check for loose battery cables and tighten them if necessary. Also, verify that the 10A main circuit breaker hasn't tripped and reset it if needed. If the main fuse is blown, replace the 100A main fuse. If none of these steps work, there may be a machine fault detected, refer to the Battery Meter LED Fault Codes.
Why won't the brush motor(s) operate on my Tennant T5E?
If the Tennant Floor Machine's brush motor(s) won't operate, start by ensuring the scrub head is lowered to the floor. Check if the battery meter lockout is activated, and if so, recharge the batteries. Also, see if the 25A circuit breaker has tripped and reset it if needed. For cylindrical brush models, inspect the belt for breakage or looseness; replace or tighten it as necessary.
What to do if my Tennant T5E will not propel?
If your Tennant Floor Machine isn't propelling, the parking brake may be set; release the parking brake lever. Check if the propel motor fuse is blown and replace the 30A fuse if necessary. Avoid steep inclines, as exceeding the maximum incline can also cause this issue; reset the key.
Why is the vacuum motor not working on my Tennant T5E Floor Machine?
If the vacuum motor on your Tennant Floor Machine isn't operating, make sure the squeegee is lowered to the floor. If the batteries are discharged, charge them. If the vacuum motor circuit breaker has tripped, reset the 25A circuit breaker button.
Why my Tennant Scrubber machine will not operate?
If your Tennant Scrubber won't operate, several issues could be the cause. First, ensure the batteries are charged. If that's not the issue, check if the emergency-stop button is activated and, if so, turn it clockwise to reset. Other potential causes include faulty batteries (replace them), a loose battery cable (tighten it), a tripped main circuit breaker (reset the 10A breaker), or a blown main fuse (replace the 100A fuse). Finally, the issue may be a machine fault, in this case consult Battery Meter LED Fault Codes.
What to do if the brush motor(s) will not operate on Tennant Scrubber?
If the brush motor(s) on your Tennant Scrubber aren't working, start by ensuring the scrub head is lowered to the floor. Check if the battery meter lockout is activated, and if so, recharge the batteries. Also, discharged batteries could be the problem, so ensure they are charged. Another possible reason is a tripped brush motor circuit breaker; if so, reset the 25A circuit breaker button. Finally, on cylindrical brush models, inspect the belt for breakage or looseness and replace or tighten it as needed.
Describes the machine's purpose and limitations.
Guidelines for safe operation before starting.
Checks and precautions before operation.
Instructions for connecting and installing batteries.
List of checks before starting the machine.
Step-by-step guide to start the machine.
Procedure for stopping the machine in an emergency.
How to set up the onboard charger for battery type.
Procedures for maintaining machine batteries.
Troubleshooting common operational issues.
Interpreting fault codes from the battery meter.
General| Brand | Tennant |
|---|---|
| Model | T5E |
| Category | Floor Machine |
| Language | English |
To Next Page
