-14-
Preparation before playing disc
u The display language is preset to English.
Please refer to Setup operation.
u Most of the functions are operated by the
remote control. The same functions can be
performed with buttons on either the remote
control or on the front panel.
Preparation
u Turn the TV on and select AV as the TV input.
u Switch on the stereo system power if the
player has been connected to a stereo system.
I. Operation for DVD features
This player will enter DVD playback mode after
the power has been turned on. Pressing the
CARD/DVD button on the remote control can
switch from Card reader mode to DVD playing
mode.
PLAY
1. Connect the AC power cord to a suitable AC
outlet (AC230-240V, 50Hz).
2. Press the STANDBY button. HELLO will be
shown on the VFD Display, the VFD Display
will then show LOAD. (Note: The disc
information will appear after several seconds.
If there is no disc in the DVD player NO DISC
will be shown on the Display).
3. Press the OPEN/CLOSE button to open the disc
tray. OPEN will be indicated on the upper right
corner of TV screen.
4. Place a disc (8cm or 12cm) onto the disc tray.
(For one- sided discs, position the disc with
printed title side facing up. For a two-sided
disc, position the side to be played facing
down).
5. Press OPEN/CLOSE again to close the disc tray.
6. Press PLAY to playback the disc. You can
follow the on-screen MENU of the DVD disc;
press ENTER or the OK button to playback.
Some discs will play themselves automatically
after being loaded.
7. Switch off the power by pushing the power
button again. BYE will appear on the Display
before shutting down.
STOP
Press the STOP button to stop playing at any time.
When playback is stopped, the unit records the
point where STOP was pressed (RESUME
function). Press PLAY again, and play will resume
from this point. Press the STOP button twice and
the RESUME function will be cancelled.
The RESUME function is suitable for discs showing
playing time during playback.
Note: Some discs including MPEG4 discs have no
such function.
STANDBY
When you press the STANDBY button, the player
will switch to Standby status. When pressed again,
the player will return to normal working status.
SKIP- / SKIP+
Press the SKIP- or SKIP+ buttons on the remote
control during playback. A chapter (DVD) or a
track (CD) is skipped back ”-“ or forward ”+”
correspondingly each time the button is pressed.
PAGE- / PAGE+ button
For multi-page menus of DVD-Audio discs, press
PAGE+/PAGE- to go to next page or previous page.
F.FWD / F.RWD
Press the F.FWD / F.RWD buttons on the remote
control during playback and the unit will enter fast
Forward / fast Reverse mode. There are 4 speeds
of fast forward (or reverse) available: x2, x4, x8,
x16 and x 32. To return to normal play, press the
PLAY button on the front panel or the remote control
again.
Note: 1. Some discs have no such function
2. For MPEG4 discs, if the played file is too small,
the speed levels of fast forward (or reverse) will
only have x2 or x4.
SLOWF / SLOWR
Press the SLOWF/SLOWR buttons on the remote
control during playback and the unit will enter slow
forward/reverse mode. There are 4 speeds
available: 1/2, 1/4, 1/6 and 1/7. To return to normal
play, press the PLAY button on the front panel or
remote control again.
Note: 1. Some discs have no such function
PAUSE / STEP
Press PAUSE/STEP button during play, the player
will enter the still picture mode. If the button is
pressed again, the disc is advanced by one frame
(step). When the button is pressed again,
consecutive frames advance. To return to normal
play, press PLAY button.
Note: 1. Some discs have not such function
NOTE: During the playing of the introduction of a
movie, PAUSE/STEP, F.FWD, F.RWD, SLOW, SKIP-
/ SKIP+ may be ineffective.
Number (0-9 button)
Use the number buttons on the remote to directly
jump to a desired track or chapter.
MUTE
Press the MUTE button during play to silence the
audio signal to the speakers, a mute picture on
screen, press MUTE again to cancel. Pressing
the VOL+ or VOL also cancels the MUTE function.
VOLUME+/-
Press VOLUME+/- button during play may change
volume for audio output. The VOLUME button has
no effect on the digital output signals.
OPERATION
DVD5000_IB.p65 05-10-22, 23:1714
To Next Page
Loading...