Need help?Do you have a question about the Thermo Scientific BB 150 and is the answer not in the manual?
General| Brand | Thermo Scientific |
|---|---|
| Model | BB 150 |
| Category | Accessories |
| Language | English |
Crucial safety guidelines for operating the CO2 incubator BB 150 safely and preventing accidents.
Outlines the terms and conditions under which Thermo Fisher Scientific warrants the incubator's operation.
Defines warning, caution, and note symbols used in the manual for clear understanding.
Specifies the correct laboratory applications and limitations for the CO2 incubator BB 150.
Lists standards and directives the device complies with.
Important safety instructions for handling and using CO2 gas with the incubator.
Lists all standard components included in the delivery of the CO2 incubator BB 150.
Step-by-step guide for checking the delivered incubator for completeness and damages.
Specifies the environmental requirements for optimal and safe operation of the incubator.
Guidelines on necessary room ventilation to safely dissipate CO2 and heat.
Details required clearances and installation space for the CO2 incubator.
Instructions on how to properly and safely transport the CO2 incubator.
Information on how to stack multiple CO2 incubator BB 150 units.
Information regarding modifications to the CO2 incubator BB 150.
Identification of all components and features visible on the front of the incubator.
Identification of all components and features visible on the rear of the incubator.
Explanation of the built-in safety mechanisms for protecting samples and users.
Details on temperature, humidity, and CO2 control within the incubator's work space.
Comprehensive guide to the automated decontamination process for the incubator.
Description of the temperature and CO2 sensors and their integration into the control system.
Information on the switchbox housing various supply interfaces and connections.
Details on the materials and design of internal components for hygiene and cleaning.
Essential steps for cleaning and preparing the incubator's interior before initial operation.
Instructions for correctly installing the adjustable shelf system inside the incubator.
Procedures for connecting the CO2 gas supply, including quality and pressure requirements.
Guidelines for safely connecting the incubator to the electrical power supply.
How to connect the CO2 incubator to a PC via the RS 232 interface.
How to connect the incubator's alarm contact to external monitoring systems.
Overview of the incubator's control panel, including displays, keys, and LEDs.
Step-by-step instructions on how to set the desired incubation temperature.
Step-by-step instructions on how to set the desired CO2 concentration.
Procedure for initiating the auto-start routine for system adjustment and calibration.
How to access and interpret error codes generated by the incubator's diagnostic system.
A detailed list of error codes, their descriptions, causes, and recommended repairs.
Procedure to reset the thermal protection after a fault.
Final checks and preparations required before releasing the incubator for operation.
A comprehensive guide to the sequence of actions for starting the incubator's normal operation.
Procedures for safely powering off and preparing the incubator for storage or maintenance.
Detailed steps for manual cleaning and disinfection of the incubator's interior and accessories.
Information on the automated 90°C decontamination routine, including phases and duration.
Instructions for starting and managing the ContraCon decontamination cycle.
How to cancel or skip phases of the ContraCon routine.
Recommended schedule for daily, annual inspections and functional checks.
Guidelines on when to perform weekly, 3-month, and annual service tasks.
Steps to prepare for accurate temperature comparison measurements and calibration.
Detailed procedure for calibrating the temperature control system of the incubator.
Steps required to prepare for CO2 comparison measurements and calibration.
Detailed procedure for calibrating the CO2 metering and regulation circuit.
Instructions for removing and installing sterile filters, particularly for gas supply.
Steps for safely replacing the internal fuses of the incubator.
Procedure for replacing the magnetic door seal.
A catalog listing part numbers for various components and accessories for the incubator.
Specifications regarding the physical dimensions, weight, and load capacity of the incubator.
Data related to ambient temperature, control range, and heat dissipation of the incubator.
Technical details on water quality requirements and humidity control performance.
Specifications related to gas purity, pressure, and control range for the CO2 supply.
Technical data for the CO2 measuring cell.
Technical data for voltage, frequency, current, and protection class of the incubator's electrical components.
Information on the disposal of the product according to the WEEE Directive.
To Next Page