Topcon ES-62 - Page 79

To Next Page

To Previous Page

6-21

6 SPECIAL MODE (Menu Mode)

4 Press the {F1} key.

The data previously set is shown.

{F1}

5 Press the {F1} (ON) key or {F2} (OFF) key, and

press the {F4} (ENTER) key.

{F1}

{F2}

{F4}

ERROR CORR. [OFF]

F1:ON

F2:OFF

ENTER

Main Page

Precautions for Safe Operation3
Precautions6
Laser Safety Information10
- Table of Contents12
1 Nomenclature and Functions16
- Nomenclature16
- Display17
- Operating Key18
- Function Key (Soft Key)19
- Star Key Mode21
- Serial Signal RS-232C Connector23
- Bluetooth Communication (Only for Built-In Bluetooth Model)23
2 Preparation for Measurement24
- Power Switch Key on24
- Battery Power Remaining Display25
- Vertical and Horizontal Angle Tilt Correction26
- How to Enter Alphanumeric Characters28
- Setting Instrument up for Measurement31
  - Centering31
  - Levelling33
- Focussing and Target Sighting35
3 Angle Measurement36
- Measuring Horizontal Angle Right and Vertical Angle36
- Switching Horizontal Angle Right/Left37
- Measuring from the Required Horizontal Angle37
  - Setting by Holding the Angle37
  - Setting a Horizontal Angle from the Keys38
- Vertical Angle Percent Grade(%) Mode38
- Repetition Angle Measurement39
- Buzzer Sounding for Horizontal Angle 90° Increments40
- Compasses (Vertical Angle)41
4 Distance Measurement42
- Setting of the Atmospheric Correction43
- Setting of the Correction for Prism Constant43
- Distance Measurement (Continuous Measurement)43
- Distance Measurement (N-Time Measurement/Single Measurement)44
- Fine Mode/Tracking Mode/Coarse Mode45
- Stake out (S.O)46
- Offset Measurement47
5 Coordinate Measurement56
- Setting Coordinate Values of Occupied Point56
- Setting Height of the Instrument57
- Setting Height of Target (Prism Height)57
- Execution of Coordinate Measuring58
6 SPECIAL MODE (Menu Mode)59
- Application Measurement (PROGRAMS)60
- Setting the GRID FACTOR74
- Setting Illumination of Display and Cross Hairs75
- Setting Mode 176
- Setting Contrast of Display83
- Road84
7 Data Collection95
- Preparation97
- Operational Procedure of DATA COLLECT101
- Data Collect Offset Measurement Mode104
- NEZ Auto Calculation111
- Point to Line Measurement112
  - To Change to the Point to Line Measurement112
  - Executing a Point to Line Measurement113
- Editing PCODE Library [PCODE INPUT]114
- Setting Parameter of Data Collect [CONFIG.]115
8 Layout116
- Preparation118
- Executing a Layout124
  - Layout of Coordinates of Point to Line126
- Setting a New Point127
  - Side Shot Method127
  - Resection Method129
9 Memory Manager Mode133
- Display Internal Memory Status134
- Searching Data135
- File Maintenance139
- Coordinate Data Direct Key Input142
  - Coordinate Data Input142
  - PTL (Point to Line) Data Input143
- Delete a Coordinate Data from a File144
- Editing PCODE Library145
- Data Communications146
- Initialization151
10 Set Audio Mode152
11 Setting the Prism Constant Value153
12 Setting Atmospheric Correction154
- Calculation of Atmospheric Correction154
- Setting of Atmospheric Correction Value155
13 Correction for Refraction and Earth Curvature157
- Distance Calculation Formula157
14 Power Source and Charging158
- Battery Charging158
- Installing/Removing the Battery159
15 Using Usb Flash Drive161
- Inserting the USB Flash Drive161
16 Detach/Attach of Tribrach162
17 Selecting Mode163
- Items of the Selecting Mode163
- How to Set Selecting Mode165
18 Checks and Adjustments167
- Circular Level167
- Adjustment of Vertical Angle 0 Datum168
- Adjustment of Compensation Systematic Error of Instrument169
- Reticle171
- Optical Plummet172
- Additive Distance Constant173
- Checking and Adjusting of Laser Plummet174
19 Top Field Mode177
- MAIN MENU (Major Functions)177
- Job177
- Setting179
- Go to Work180
- Data Manager192
20 Precautions201
21 Special Accessories202
22 Battery System204
23 Prism System205
24 Error Displays206
25 Regulations208
26 Specifications211
Appendix215
- Target for Laser Plummet Adjustment215

Topcon ES-62 - Page 79

Table of Contents

Related product manuals