Toro GrandStand 74504TE Service Manual

Toro GrandStand 74504TE

64 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

SERVICE MANUAL

Grandstand

LCE Products

Issued: February 2016

Table of Contents

Other manuals for Toro GrandStand 74504TE

Operator's Manual60 pages

Questions and Answers:

S
Stephanie BurkeAug 13, 2025
Why won't my Toro GrandStand 74504TE engine start?
- B
  Bethany DaltonAug 14, 2025
  If your Toro Lawn Mower engine won't start, starts with difficulty, or stops running, there are several potential causes: * The fuel tank may be empty, or the shutoff valve might be closed. Refuel the tank and ensure the valve is open. * The choke control could be disengaged; engage it. * A spark-plug wire might be loose; attach it securely to the spark plug. * The spark plug may be faulty; replace it with a new, correctly gapped one. * A dirty air cleaner can cause this issue; service the air-cleaner element. * The fuel filter may be clogged with dirt; replace it. * If dirt, water, or stale fuel is in the fuel system, please contact an Authorized Service Dealer. * If the gap between the safety-interlock switches is not correct, please contact an Authorized Service Dealer.
A
Ann DouglasAug 17, 2025
Why does my Toro GrandStand 74504TE engine lose power?
- K
  Katelyn LawsonAug 17, 2025
  If your Toro Lawn Mower engine is losing power, consider these possible reasons: 1. The engine load may be excessive. Try reducing the ground speed. 2. A dirty air cleaner can cause power loss; service the air-cleaner element. 3. Low oil level in the crankcase can be a factor; add oil. 4. Check for obstructions in the cooling fins and air passages under the engine blower housing and remove them. 5. A faulty spark plug can cause power loss; install a new, correctly gapped spark plug. 6. A plugged vent hole in the fuel cap can be the culprit; clean or replace the fuel cap. 7. A dirty fuel filter can restrict fuel flow; replace the fuel filter. 8. If dirt, water, or stale fuel is in the fuel system, please contact an Authorized Service Dealer.
C
Christopher JacobsAug 21, 2025
How to fix uneven cutting height on my Toro GrandStand 74504TE?
- T
  Thomas JohnsonAug 21, 2025
  If your Toro Lawn Mower is producing an uneven cut, several factors could be responsible: * Dull blades; sharpen them. * Bent cutting blades; replace them. * The mower deck might not be level; level the mower deck side-to-side. * The mower deck pitch could be wrong; adjust the front-to-rear pitch. * A dirty mower deck underside; clean it. * Incorrect tire pressure; adjust it. * If a blade spindle is bent, please contact an Authorized Service Dealer.
P
Peggy BryantAug 25, 2025
What to do if my Toro GrandStand 74504TE Lawn Mower does not drive?
- J
  John DeckerAug 26, 2025
  If your Toro Lawn Mower isn't moving, consider the following: * The hydraulic-fluid reservoir may be low; add hydraulic fluid. * Air may be in the hydraulic system; bleed the air out. * A pump-drive belt may be slipping; replace it. * A pump-drive belt idler spring may be missing; replace it. * The pump-bypass valves may be open; tighten them to 12 to 15 N?m (9 to 11 ft-lb).
Y
ydavisAug 28, 2025
Why is my Toro Lawn Mower engine overheating?
- T
  Tracey SanchezAug 29, 2025
  If your Toro Lawn Mower engine is overheating, check the following: * The engine load may be too high; reduce the ground speed. * The oil level in the crankcase may be low; add oil. * The cooling fins and air passages under the engine blower housing may be blocked; remove any obstructions.
S
Sylvia TylerSep 1, 2025
What to do if Toro GrandStand 74504TE Lawn Mower has abnormal vibration?
- D
  Dr. Kevin BeasleySep 1, 2025
  If your Toro Lawn Mower is vibrating excessively, consider these potential causes: * Bent or unbalanced cutting blade(s); install new cutting blade(s). * A loose blade-mounting bolt; tighten it. * Loose engine-mounting bolts; tighten them. * A loose engine pulley, idler pulley, or blade pulley; tighten the appropriate pulley. * If an engine pulley is damaged, please contact an Authorized Service Dealer. * If a blade spindle is bent, please contact an Authorized Service Dealer.
R
Ruth ReedSep 8, 2025
Why won't the clutch engage on my Toro GrandStand 74504TE?
- P
  Pam GreeneSep 8, 2025
  If the clutch on your Toro Lawn Mower isn't engaging, check these potential causes: * A blown fuse; replace it. * Low voltage supply at the clutch; check the coil resistance, battery charge, charging system, and wiring connections, and replace components if necessary. * A damaged coil; replace the clutch. * Inadequate current supply; repair or replace the clutch lead wire or electrical system. Clean the connector contacts. * The rotor/armature air gap is too large; remove the shim or replace the clutch.

Toro GrandStand 74504TE Specifications

General

Engine Displacement	726cc
Transmission	Hydrostatic
Spindle Material	Cast Aluminum
Cutting Height	1.5 - 5 inches
Drive Tires	20 x 10-8
Caster Tires	13 x 6.5-6
Cutting Width	48 inches
Blade Tip Speed	18, 500 ft/min
Deck Type	Fabricated
Speed	10 mph

Related product manuals

Preview: Toro GrandStand 74504

Toro GrandStand 74504

Toro GrandStand 74505

Preview: Toro GrandStand 74574

Toro GrandStand 74574

Preview: Toro GrandStand 74534

Toro GrandStand 74534

Preview: Toro GrandStand 74589

Toro GrandStand 74589

Toro GrandStand 74550

Preview: Toro GrandStand 74583

Toro GrandStand 74583

Toro GrandStand 74578

Preview: Toro GrandStand 74558

Toro GrandStand 74558

Preview: Toro GrandStand 74553

Toro GrandStand 74553

Preview: Toro GrandStand 74534TE

Toro GrandStand 74534TE

Preview: Toro 74534TE GrandStand

Toro 74534TE GrandStand