70
Tray loading capacity of Finisher
Upper Tray
With mixed paper not loaded
Mode Non-Sort
A4, A5-R, B5, LT, ST-R, 8.5"SQ, 16K
36.75 mm
(250)
A3, A4-R, B4, B5-R, FOLIO, 305 mm x 457 mm, LD, LG, LT-R,
COMP, 13"LG, 12"x18", 8K, 16K-R
18.4 mm
(125)
Lower Tray
With mixed paper not loaded
Mode Non-sort Sort/Group Front/Rear Single Position Stapling Two Positions Stapling
A4, B5, LT, 8.5"SQ, 16K
350 mm
(3000)
350 mm
(3000)
Whichever of 100 sets or 2000
sheets is reached rst
Whichever of 150 sets or 2000
sheets is reached rst
A3, A4-R, B4, FOLIO, LD, LG,
LT-R, COMP, 13"LG, 8K
175 mm
(1500)
175 mm
(1500)
Whichever of 50 sets or 1000 sheets
is reached rst
Whichever of 75 sets or 1000 sheets
is reached rst
• When mixed-size paper is loaded, the tray loading capacity should follow the specications for larger paper sizes in the above tables.
• For the loading capacity of the saddle stitch tray, refer to the following guide:
& Copying Guide (PDF): “Chapter 3: BASIC COPY MODES” - “Selecting Finishing Mode”
Unit: mm (with allowable error of ±7mm or 0.28")
Values in parentheses: Number of sheets (80g/m
2
or 20 lb. Bond)
Hole Punch Unit
Model name MJ-6102 Series
Acceptable paper size A3, A4, A4-R, B4, B5, B5-R, FOLIO, LD, LG, LT, LT-R, COMP, 8.5"SQ, 13"LG, 8K, 16K, 16K-R
Acceptable paper weight 64 - 256 g/m
2
, 17 lb. Bond - 140 lb. Index (Transparencies or specially-treated paper are not available)
Dimensions 112 mm (4.41") (W) x 573 mm (22.56") (D) x 323 mm (12.72") (H) (excl. Lower cover)
Weight Approx. 7 kg (15.4 lb.)
Numbers of punching holes and hole diameter Available paper size
Japan and most of Europe
(MJ-6102E)
2 holes
(6.5 mm or 0.26" dia.)
A3, A4, A4-R, B4, B5, B5-R, FOLIO, LD, LG, LT, LT-R,
COMP, 8.5"SQ, 13"LG, 8K, 16K, 16K-R
North America
(MJ-6102N)
2/3 holes switchable
(8.0 mm or 0.32" dia.)
2 holes: A4, B4, B5, B5-R, FOLIO, LT, LG, 13"LG, COMP,
8.5"SQ, 16K
3 holes: A3, A4, LD, LT, 8K, 16K
France
(MJ-6102F)
4 holes
(6.5 mm or 0.26" dia.; 80 mm or 3.15" pitch)
A3, A4-R, LT-R, LD, 8K, 16K
Sweden
(MJ-6102S)
4 holes
(6.5 mm or 0.26" dia.; 70 mm and 21 mm or 2.76
and 0.83" pitch)
A3, A4, A4-R, B4, B5, B5-R, FOLIO, LD, LG, LT, LT-R,
COMP, 8.5"SQ, 13"LG, 8K, 16K, 16K-R
FAX Unit
Model Name GD-1270
Size of Original A3, A4, A4-R, A5, A5-R, B4, B5, B5-R, FOLIO, LD, LT-R, LG, ST, ST-R, COMP
Recording Paper Size
A3, A4, A4-R, A5-R, B4, B5, B5-R, FOLIO, LD, LG, LT, LT-R, ST-R, COMP
Compatibility
Communication Modes
Exclusive Mode, ECM, G3
Communication
Resolution
Horizontal: 8 dots/mm, 16 dots/mm, 300 dots/inch
Vertical: 3.85 lines/mm, 7.7 lines/mm, 15.4 lines/mm, 300 dots/inch
Transmission Rate 33,600/31,200/28,800/26,400/24,000/21,600/19,200/16,800/14,400/12,000/9,600/7,200/4,800/2,400 bps
Encoding Systems JBIG/MMR/MR/MH
Printing Method Laser electronic printing
Memory Capacity Transmission/Reception: 1 GB (HDD)
*1
Unit Type Desktop type, transmitting/receiving dual type
Applicable Network Public Switched Telephone Network (PSTN)
*1 For hard drives, MB means 1 million bytes. (Total HDD accessible capacity may vary depending on operating environment.)
For details of the FAX Unit (GD-1270), refer to the following guide:
& GD-1250/GD-1260/GD-1270 Operator’s Manual for FAX Unit: “Chapter 1: BEFORE USING FAX”
Toshiba-recommended paper is used for the values above. Specications and appearance are subject to change without
notice in the interest of product improvement.
To Next Page
Loading...
