Toshiba RAS-10JAVP-E - Remote Controller and Its Fuctions

– 39 –
8-6. Remote Controller and Its Fuctions
8-6-1. Parts Name of Remote Controller
1 Infrared signal emitter
Transmits signal to the indoor unit.
2 button
Push the button to start operation.
(A receiving beep is heard.)
Push the button again to stop operation.
(A receiving beep is heard.)
If no receiving sound is heard from the indoor unit,
push the button twice.
3 Mode select button (MODE)
Push this button to select a mode.
Each time you push the button, the modes cycle in
order from A : Auto changeover control,
: Cool,
: Dry, : Heat and back to A.
(A receiving beep is heard.)
4 Temperature button (
TEMP
)
.....The temperature setting is increased to 30°C.
.....The temperature setting is reduced to 17°C.
(A receiving beep is heard.)
5 Fan speed button (FAN)
Push this button to select the fan speed. When you
select AUTO, the fan speed is automatically adjusted
according to the room temperature.
You can also manually select the desired fan speed
from five available settings.
(LOW
, LOW
+
, MED , MED
+
,
HIGH
) (A receiving beep is heard.)
6 Auto louver button (SWING)
Push this button to swing the louver.
(A receiving beep is heard.)
Push the FIX button to stop the louver from swinging.
(A receiving beep is heard.)
7 Set louver button (FIX)
Push this button to adjust the air flow direction.
(A receiving beep is heard.)
8 ON timer button (ON)
Use this button to change the clock and ON timer
times.
To move up the time, push
of the “ON
ON
” button.
To move down the time, push
of the “ON
ON
”
button.
9 OFF timer button (OFF)
Use this button to change the OFF timer times.
To move up the time, push
of the “OFF
OFF
” button.
To move down the time, push
of the “OFF
OFF
”
button.
10 Reserve button (SET)
Push this button to store the time settings.
(A receiving beep is heard.)
11 Cancel button (CLR)
Push this button to cancel the ON timer and OFF
timer. (A receiving beep is heard.)
12 High power button (Hi POWER)
Push this button to start high power operation.
13 Memory button (MEMO)
Push this button to ready for storing the settings.
Hold down the button for more than 3 seconds to
store the setting indicated on the remove control and
until the
P
mark is displayed.
14 Automatic operation button (AUTO)
Push this button to operate the air conditioner
automatically. (A receiving beep is heard.)
15 ECO timer button (ECO)
Push this button to operate the air conditioner
economically.
16 FILTER button
Push this button to turn off the filter cleaning indica-
tor on the indoor unit.
Push this button after cleaning the air filter.
17 PRESET button
Push this button to operate the air conditioner to the
settings stored using the MEMO button.
18 Air purifying button (PAP)
Push this button to start the electrical air purifying
operation.
Push the button again to stop operation.
19 Sleep time button (SLEEP)
Push this button to start the sleep timer (OFF timer)
operation.
You can select the OFF timer time from among four
settings (1, 3, 5 or 9 hours).
TEMP
PAP
MODE
AUTO
PRESET
Hi POWER
SWING
CLR
FIX FAN SLEEP
ECO MEMO
SET
FILTER
CLOCK
RESET
CHECK
ON OFF
AUTOA
AM
PM
CHK
HiPOWER
ON
OFF
C
:
AM
PM
:
P
AUTO
UTO
1
17
15
8
3
18
4
12
6
11
13
5
9
7
10
19
16
14
2