Toshiba RAS-B10SKVP-E - AUTO RESTART OPERATION; ENABLING AND DISABLING AUTO RESTART


1616
ENEN
This air conditioner is equipped This air conditioner is equipped with an automatic restarting function which allows the air conditioner with an automatic restarting function which allows the air conditioner to resume without the use of theto resume without the use of the
remote controller under the operating settings in the event of a power shutdown. Operation resumes without warning 3 minutes afterremote controller under the operating settings in the event of a power shutdown. Operation resumes without warning 3 minutes after
power is restored.power is restored.
TTo set the o set the auto restart function, proceed auto restart function, proceed as follows:as follows:
The power supply to the unit The power supply to the unit must be on. The function will must be on. The function will not be set if the not be set if the power is off.power is off.
TTo enable the o enable the auto restart function, hold auto restart function, hold down the RESET button for 3 down the RESET button for 3 seconds.seconds.
The air conditioner receives the setting and beeps 3 The air conditioner receives the setting and beeps 3 times. The system now restartstimes. The system now restarts
automaticallyautomatically. The auto . The auto restart setting is arestart setting is a ctivated.ctivated.
(1) (1) When the air When the air conditioner is in sconditioner is in stand-by (not tand-by (not running).running).
Hold down the RESET button for 3 seconds or more.Hold down the RESET button for 3 seconds or more.
•• The air conditThe air conditioner starts to ioner starts to operate. The operate. The green indicator green indicator turns on.turns on.
•• After about After about 3 seconds, 3 seconds, the air the air conditioner beeps conditioner beeps 3 times.3 times.
The green indicator flashes for 5 seconds.The green indicator flashes for 5 seconds.
•• The air The air conditconditioner ioner is opeis operatirating.ng.
If the air conditioner is not required If the air conditioner is not required to run at this time, push the to run at this time, push the RESET buttonRESET button
again or use the remote controller to again or use the remote controller to stop the air conditioner.stop the air conditioner.
(2) (2) When the When the air conditioner air conditioner is operating.is operating.
Hold down the RESET button for 3 seconds or more.Hold down the RESET button for 3 seconds or more.
•• The air conditThe air conditioner stops ioner stops operating. The operating. The green indicator green indicator turns off.turns off.
•• 3 seconds after 3 seconds after pushing the bpushing the button, the air utton, the air conditioner beeps 3 tconditioner beeps 3 times.imes.
The green indicator flashes for 5 secondsThe green indicator flashes for 5 seconds
•• The aThe air cir conditonditioner ioner stopsstops..
If you do not need the air If you do not need the air conditioner to stop at this time, use the remote controller to conditioner to stop at this time, use the remote controller to restart the air conditioner. During therestart the air conditioner. During the
subsequent operation, the green indicator is turned on.subsequent operation, the green indicator is turned on.
•• The auto restart operation will not accThe auto restart operation will not accept a command if timeept a command if timer operation with the remotr operation with the remote controller is active controller is activated.ated.
•• After restarting the air conditioner by the AUTO RESTAfter restarting the air conditioner by the AUTO RESTART OPERAART OPERATION, the louver swing (AUTTION, the louver swing (AUTO) operation resumes.O) operation resumes.
TTo cancel the o cancel the auto restart operation, proceed auto restart operation, proceed as follows:as follows:
Repeat the setting procedure. The air conditioner receives the setting and beeps Repeat the setting procedure. The air conditioner receives the setting and beeps 3 times.3 times.
The air conditioner now needs to The air conditioner now needs to be manually restarted with the remote controller after the be manually restarted with the remote controller after the main supply is turned off.main supply is turned off.
The auto restart setting is cancelled.The auto restart setting is cancelled.
(1) (1) When the air When the air conditioner is in sconditioner is in stand-by (not tand-by (not running).running).
Hold down the RESET button for 3 seconds or more.Hold down the RESET button for 3 seconds or more.
•• The air conThe air conditioditioner staner starts to operrts to operate.ate.
The green indicator will turn on.The green indicator will turn on.
•• After about After about 3 seconds, 3 seconds, the air the air conditioner beeps conditioner beeps 3 times3 times..
•• The air The air conditconditioner ioner is opeis operatirating.ng.
If the air conditioner is not required If the air conditioner is not required to run at this time, push the to run at this time, push the RESET buttonRESET button
again or use remote controller to stop the again or use remote controller to stop the air conditioner.air conditioner.
(2) (2) When the When the air conditioner air conditioner is operating.is operating.
Hold down the RESET button for 3 seconds or more.Hold down the RESET button for 3 seconds or more.
•• The air cThe air conditonditioner sioner stops otops operatperating.ing.
The green indicator is turned The green indicator is turned off.off.
•• After about After about 3 seconds, 3 seconds, the air the air conditioner beeps conditioner beeps 3 times3 times..
•• The aThe air cir conditonditioner ioner stopsstops..
If you do not need the air conditioner to stop aIf you do not need the air conditioner to stop at this time, use the remote controllert this time, use the remote controller
to restart the air conditioner.to restart the air conditioner.
During subsequent operation, the green indicator is turned During subsequent operation, the green indicator is turned on.on.
AUTO RESTART OPERATION
AUTO RESTART OPERATION
INFORMATIONINFORMATION

INFORMATION
INFORMATION
The AUTO RESTThe AUTO RESTART OPERAART OPERATION is not TION is not set to work at set to work at factory shipment, and so factory shipment, and so it is necessary it is necessary to set it to set it to this function ifto this function if
required.required.
HOW TO SET HOW TO SET AUTO RESTARTAUTO RESTART
HOW TO CANCEL AUTO RESTARTHOW TO CANCEL AUTO RESTART
RESET buttonRESET button
RESET buttonRESET button