Toshiba RD-97DTKB - DVC to HDD; DVD Dubbing

49
EN
Introduction Connections Basic Setup Playback
Editing
Others
Function Setup
Recording
DVC to HDD / DVD Dubbing
Before recording from DVC, see page 22 for
connection instructions.
If you are dubbing to the HDD, press [HDD] first.
If you are dubbing to a disc, press [DVD] first.
1 Select “DV” channel using
[INPUT SELECT F] or
[PROG. G / H].
2 Press [REC MODE] to select a
recording mode. (See page 33.)
3 Press [DISPLAY].
4 With “Control” highlighted, press
[ENTER/OK] to display the available
devices to control with the remote
control of this unit. Select “DVC”
using [U \ D], then press
[ENTER/OK].
e.g.) DVC to DVD dubbing
Now you can operate your DVC with the remote
control of this unit.
5 Press [PLAY B] to start playing back
the DVC, and find the point where
you wish to start dubbing.
Press [STOP C] when you come to
the desired start point.
6 Select “Start Rec” using [U \ D],
then press [ENTER/OK].
The dubbing will start.
To stop dubbing;
1 Select “Control” using [U \ D], then press
[ENTER/OK].
2 Select “HDD” or “DVD” using [U \ D]
(whichever the recording component you
are using), then press [ENTER/OK].
3 Press [STOP C].
Note
• If you press [PAUSE F] at step 5, the tape will
rewind to the point a few seconds preceding the
paused point when you press [ENTER/OK] at step
6, then, it will start dubbing when it comes to the
paused point.
• The unit does not send out the output signal to DVC.
• For the proper operation, connect DVC to the unit
directly. Do not connect this unit and DVC via any
other unit.
• Do not connect more than one DVC.
• The unit can only accept DVC. Other DV device
such as cable/satellite box or D-VHS VCR cannot be
recognised.
• If no video signal is detected from the DVC during
DVC to HDD / DVD dubbing, the recording will be
paused and “I” will flash on the TV screen. The
recording will resume when the unit detects the
video signal again.
• When the DVC is in camera mode, refer to “Guide to
DV and On-Screen Display” on page 48.
• Date / time and cassette memory data will not be
recorded.
• Pictures with a copy-guard signal cannot be
recorded.
• A DV terminal is a terminal that can use the
transmission mode conforming to the IEEE 1394
standards called “Fire Wire”. It serves as the
interface that connects the PC and peripheral device
such as “i.Link” (registered trademark of SONY). It
enables digital dubbing between DV devices with
little degradation.
• You cannot dub from DVC to the both HDD and DVD
at the same time.
Preparing for DV dubbing (DVC to HDD):
• Make sure your DVC is in video mode.
Preparing for DV dubbing (DVC to DVD):
• Insert a recordable DVD.
• Make sure your DVC is in video mode.
HDDHDD
D
D
VD-R
VD-R
W
W
DVD-RW
Video
DVD-RWDVD-RW
VR
DVD-RDVD-R
D
D
VD+R
VD+R
W
W
DVD+RW D
D
VD+R
VD+R
DVD+R
AB-1234
0:00:00
DV
AB-1234
0:00:00
DV
DV Audio Stereo1
Start Rec
Control DVD
1/ 1 1/ 1
DVD SP 2:00
- RW VR ORG
T C
E2J70BD_EN.book Page 49 Friday, June 29, 2007 2:50 PM