Toshiba RD-97DTKB - One-Touch Timer Recording (OTR); Timer Recording

40
EN
One-touch Timer Recording
(OTR)
This is a simple way to set the recording time in blocks
of 30 minutes. Check that the disc you are recording
onto has enough space remaining for the time you
set.
1 Follow steps 1 to 6 in “Basic
Recording” on page 39.
2 Press [REC I] repeatedly until the
desired recording time (30 minutes
to 8 hours) appears on the TV
screen.
One-touch Timer Recording will start.
• When the unit reaches the specified time, it will
be turned off automatically.
• To change the recording length during One-
touch Timer Recording, press [REC I]
repeatedly until the desired length appears.
• To cancel One-touch Timer Recording within the
specified time, press [STOP C].
Hint
• The remaining recording time will appear on the TV
screen during One-touch Timer Recording. Press
[DISPLAY] to see it on the TV screen.
• The remaining recording time will be displayed on
the front panel display during One-touch Timer
Recording.
• Unlike the timer recording, you can perform the
following operations during One-touch Timer
Recording.
- Turn off the power. (One-touch timer recording will
be cancelled.)
-Use [REC I] or [STOP C] on the remote control.
Note
• You cannot use the pause function during One-
touch Timer Recording.
• The unit will be turned off automatically under the
following conditions.
- No space remains on the disc.
- If a power failure occurs.
• If you want to monitor the programme that you are
recording, make sure the device such as a Satellite
Box is powered off or press [DISPLAY] when it is
connected to AV2.
Timer Recording
You can set the unit to record up to 36 programmes,
up to a month in advance. Daily or weekly programme
recordings are also available.
• Be sure to set the clock before entering a timer
programming.
Insert a recordable disc.
1 In stop mode, press [TIMER PROG.].
Timer Programming list will appear.
2 Select “New Program” using
[U \ D], then press [ENTER/OK].
• If there are 7 programmes or more, use
[SKIP H / G] to turn the page.
3 Enter the date using [U \ D], then
press [P].
Each time you press [D] at the current date, the
timer recording date will change as follows.
e.g., 1st January
4 Enter the time to start and to end
using [U \ D], then press [P].
HDDHDD
D
D
VD-R
VD-R
W
W
DVD-RW
Video
DVD-RWDVD-RW
VR
DVD-RDVD-R
D
D
VD+R
VD+R
W
W
DVD+RW D
D
VD+R
VD+R
DVD+R
0:30
8:00 7:30
1:00
Normal
Recording
HDDHDD
D
D
VD-R
VD-R
W
W
DVD-RW
Video
DVD-RWDVD-RW
VR
DVD-RDVD-R
D
D
VD+R
VD+R
W
W
DVD+RW D
D
VD+R
VD+R
DVD+R
Timer Programming
1/1
0:00 THU 06/12
Date
06/12
07/12
Start
7:00
9:00
End
9:00
9:30
CH
18
190
New Program
STTL
PDC
Daily
M-F (Mon.-Fri.)
01/01
31/01
W-SAT
W-FRI
W-SUN
Timer Programming
1/1
Skip
CH
Off
901
Date
REC To
01/01
HDD
XP 1:00
Mode
Start
XP
- : -
STTL
OFF
End
- : -
0:00 THU 06/12
E2J70BD_EN.book Page 40 Friday, June 29, 2007 2:50 PM