TQC AB6000 - 10.4 Tools; 10.4.1 Small Sponge (AB5012); 10.4.2 Wild Boar Brush (AB5010); 10.4.3 Nylon Brush (AB5011)

| 24
The TQC Scrub, Abrasion and Washability Tester can be supplied with a wide range of tools. These tools are all selected and produced with the greatest care.
Please see the Ordering Matrix to select the correct tool for the appropriate standard. You can download the Ordering Matrix at
www.tqc.eu/en/product/tqc-scrub-abrasion-and-washability-tester/ under the tab documents.
10.4 Tools
The small sponge holder is supplied ready for use.
The sponge is a gentle tool to test the washability
of the coating. Often used for cleanability tests of
for example wall paints.
Placement
The AB5012 sponge tool is placed in the AB5042
or AB5041 holder and needs to fit comfortably in
the holder. The tool must be able to move freely
without friction in the holder. Always position
the tool facing the same way, to create the best
homogeneity in results. For replacement intervals
check the appropriate standard.
Scope of supply:
• Sponge
• Sponge Holder
• Weight 60 g / 0.13 oz
• Weight 100 g / 0.22 oz
• Fixation Screw
Specications Sponge Tool Complete
Mass: 508 g / 17.92 oz
Standards: ASTM D4213-92, ASTM D4828
Specications Sponge Tool Holder
Material: Stainless steel
Inner dImensions: 92x41 mm
Outer dimensions 94x43 mm
Scope of supply
• Wild boar brush
• Brush holder
• Weight
Specications Wild Boar Brush Tool Complete
Mass: 250g/8.82oz
Standards: DIN 53778
Specications Brush Holder
Inner dimensions: 92x41 mm
Outer dimensions: 94x43 mm
Material: Stainless steel
Specications Wild Boar Brush
Material: Wild boar hair
Mass: 60 g / 0.13 oz
Scope of supply
• Nylon brush
• Brush holder
• Weight 60 g / 0.13 oz
• Weight 100 g / 0.22 oz
• Fixation screw
Specications Nylon Brush Tool Complete
Mass: 454 g / 16.01 oz
Standards: ASTM D2486
Specications Brush Holder
Material: Stainless steel
Inner dimensions: 92x41 mm
Outer dimensions: 94x43 mm
The wild boar brush holder is supplied ready for
use. The brush is used to test scrub resistance of
coatings. The brushes are not worn in. This needs
to be done on the machine of the user.
Placement
The AB5010 Wild boar hair tool is placed in
the AB5042 or AB5041 holder and needs to fit
comfortably in the holder. The tool must be able
to move freely without friction in the holder.
Always position the tool facing the same way,
to create the best homogeneity in results. For
replacement intervals check the appropriate
standard.
The nylon brush brush holder is supplied ready
for use. The brush is used to test scrub resistance
of coatings. The brushes are not worn in. This
needs to be done on the machine of the user.
Placement
The AB5011 nylon brush tool is placed in the
AB5042 or AB5041 holder and needs to fit
comfortably in the holder. The tool must be able
to move freely without friction in the holder.
Always position the tool facing the same way,
to create the best homogeneity in results. For
replacement intervals check the appropriate
standard.
10.4.1 Small Sponge (AB5012)
10.4.2 Wild Boar Brush (AB5010)
10.4.3 Nylon Brush (AB5011)