Trane Air-Fi WCS-SB/R

To Next Page

To Previous Page

BAS-SVX40K-EN

Figure 12. Wiring SC+ WCI coordinators using PM014

Figure 13. Wiring the WCI coordinator to a Tracer SC+ when IMC power budget allows (wiring a

WCI to Symbio™ 800 similar)

WCI Installation

Main Page

Table of Contents5
Overview9
Air-Fi® Wireless Communications Interface (WCI)9
Air-Fi® Wireless Communications Sensor (WCS)9
Compatibility with Previous Generation Wireless Zone Products9
Wired Zone Sensors9
Devices Supported by Air-Fi® Wireless Systems9
Maximum Number of Air-Fi® Devices and Networks Allowed10
Automatic Network Formation and Sensor Association11
Network Security11
Air-Fi® Device Part Numbers12
Firmware Requirements for Devices on an Air-Fi® Network12
WCI Dimensions14
WCS-SB/SD Dimensions15
WCS-SO/SCO2 Dimensions (WCS-SB/R Similar)16
Specifications17
Agency Compliance21
Pre-Installation22
Location Considerations22
WCI Positioning22
Line of Sight Placement22
WCI Maximum Wire Length22
WCI Installation Locations22
WCS Installation Locations23
WCS Height Requirements23
WCS Mounting Surfaces24
Design Consideration for BCI-I, BCI-R, BCI2-I and BCI2-R24
WCI Installation25
WCI Addressing25
WCI Mounting and Wiring26
Controller Applications26
Repeater Applications34
Changing a WCI from Device Association to Repeater34
WCS-SB/SD Installation35
Powering the WCS35
WCS Addressing35
WCS: Network Joining and Controller Association39
2% Relative Humidity Sensor Module39
WCS : Points and Referencers39
Mounting the Sensor Back Plate40
Wcs-So/Sco41
And -SB/R Installation41
Powering the WCS-SO, -SCO 2 , -SB/R Sensor41
Addressing the WCS-SO, -SCO 2 , -SB/R Sensor41
WCS-SO, -SCO 2 , -SB/R Network Joining and Controller Association44
WCS : Points and Referencers44
Mounting the WCS-SO, -SCO , -SB/R Sensor Back Plate44
Wiring an External Sensor Probe to WCS-SB/R45
WCS-SO, -SCO 2 , -SB/R Display Sequence48
RH Sensor Module Installation50
Replacing the Sensor Cover51
WCS-SO, -SCO 2 , -SB/R Error Codes51
Testing WCS-To-WCI Signal Strength and Battery Life52
WCS-SB/SD Configuration53
Configuration Procedure53
Example of a Configured WCS-SD Display56
Optional Features56
Displaying Setpoint or Temperature56
Locking or Unlocking Settings57
Star (*)/Double Star (**) Function58
Replacing the Sensor Cover58
Viewing Unit Controller Operating Status59
Establishing an Air-Fi® Network60
WCI Leds and Buttons60
Three Ways to Establish an Air-Fi® Network62
Establishing the Network after Tracer SC+ Installation63
Installation63
Task 1: Activate Communication Among Existing Wcis63
Task 2: Installing a Tracer SC+ after Network Formation64
Installing Air-Fi Wireless Sensors with Bacnet MS/TP or Bacnet/Ip64
Modifying an Air-Fi® Network68
Adding Wcis to an Existing Network Using Tracer TU68
Adding Wcis to an Existing Network Using a WCI68
Adding Coordinators to a Tracer SC68
Removing a WCI from a Network68
Replacing a WCI on a Network69
Moving a WCI from One Device to Another69
Changing the Zigbee® Channel of the Wireless Network69
Closing the Network69
Disbanding a Network69
Troubleshooting and Maintenance70
WCI Does Not Join Network70
Tracer SC+ Does Not Communicate with WCI70
Sensor Does Not Communicate with WCI71
No Communication71
Slow Communication71
Zigbee® and Wi-Fi Channel Information72
Replacing a Failed WCI72
Task 1: Remove the Failed WCI73
Task 2: Install the New WCI73
Testing WCS Signal Quality and Battery Life74
Checking Signal Quality on a Site74
Battery Information75
Manual Association Process76
Disassociation76
Replacing a Failed WCS76
Sensor Output Power Level77
Cleaning the Sensor77
Using the Tracer® TU Service Tool with a Wireless Network78
Requirements for Joining a Wireless Network78
Joining Tracer TU to a Wireless Network78
Managing a Wireless Network and Devices80
Connecting to a Device80
The Wireless Menu81
Wireless Sensor Setup88
Default Sensor Values for Trane® Standard Programs89
Referencing Individual Sensors89
BCI/BCI2 Point and Reference Limitations91
WCS-SB/R Refrigerator Temperature Sensor Setup93
WCS-SB/R Refrigerator Sensor Plus Two Averaged Space Temp Sensors94
Setup Instructions94
Setting up Wireless Battery Monitoring98
How to Connect Air-Fi® Wireless Sensors Directly to SC100
How to Set-Up Air-Fi Network on Tracer Synchrony100
Unit Controller101
Opening Air-Fi Network102
Configuring WCS Sensor102
Creating Points to the Sensor102
Communication History104
Overview104
User Interface105
Channel Quality Scan Tool107
Overview107
Changing a Zigbee Channel109
Multiple Uses109
Scanning and Exporting (Saving) Scan Data110
Hover Information110

Trane Air-Fi WCS-SB/R - Page 30

Table of Contents

Related product manuals