What to do if Trane Tracker Version 12 Air Conditioner Tracker controller did not discover UCMs?
If the Tracker controller did not discover UCMs when initially started, verify the correct wiring of the Comm5 communication link (UCMs can only be discovered if Comm5 communication has been established). Allow at least 5 minutes for the controller to discover the UCMs.
What to do if Trane Tracker Version 12 Air Conditioner touch screen beeps but does not progress?
If the touch screen beeps when touched but does not progress to the next screen, perform the procedures for calibrating the touch screen as described in the Tracker Building Automation System Controller Operations guide.
How to troubleshoot Trane Tracker Version 12 Air Conditioner Tracker controller not communicating by EIA-232 port?
If the Tracker controller does not communicate via the EIA-232 port, verify that the cable is connected to the PC direct connect port. Ensure the correct cable is used and that the PC workstation uses Tracker controller software. Check for activity on the PC RX LED.
How to fix Trane Tracker Version 12 Tracker controller not communicating by modem?
If the Tracker controller does not communicate by modem, verify that the telephone cable is connected to the PC modem port. Make sure the phone line is analog, not digital. Then, perform the modem self-test procedure from the display module.
Why is outdoor air temperature not reading correctly on my Trane Tracker Version 12?
If the outdoor air temperature is not reading correctly on your Trane Air Conditioner, measure the resistance of the outdoor air temperature thermistor (preferably at the termination module) and check the measurement against the provided table. Also, inspect the location of the outdoor air temperature sensor.
How to adjust touch-screen back light and contrast on Trane Tracker Version 12?
If the touch-screen back light and contrast are out of adjustment on your Trane Air Conditioner, perform the adjust brightness and contrast procedure from the display module.
Describes the three main components: termination, main, and display modules.
Details the housing, termination board, and cable access of the termination module.
Explains the main module's housing, logic board, and Ethernet board functionality.
Covers the display module's housing, LCD touch screen, and alarm LED.
Explains how model numbers identify controller information and defines each digit.
Lists detailed technical specifications for the Tracker controller, including power, environment, and dimensions.
Details the maximum number and types of Unit Control Modules (UCMs) for Tracker models 12 and 24.
Outlines the maximum number and types of Unit Control Modules (UCMs) for the Tracker model WSHP.
Provides essential pre-installation steps including shipment verification, damage inspection, and storage.
Guides selection of a suitable, secure, and accessible indoor location for the controller.
Ensures the chosen location meets the controller's environmental and operational specifications.
Confirms adequate space for the controller and necessary ventilation, cable, and service access.
Ensures the controller is mounted at a height and location that allows optimal touch screen viewing.
Provides instructions for physically attaching the termination module to a wall or conduit box.
Details the process for installing electrical conduit for wire entry into the termination module.
Explains how to connect the 24 Vac power supply to the termination board terminals.
Covers wiring specifications and procedures for optional inputs and outputs like alarm relay and sensors.
Provides steps for wiring the alarm relay output to the termination board.
Details the procedure for wiring a priority shutdown device input to the termination board.
Explains how to wire the utility pulse meter input to the termination board.
Provides instructions for wiring the thermistor input for outdoor air temperature sensing.
Covers wiring Unit Control Modules (UCMs) to the Tracker termination board via the Comm5 link.
Explains the correct placement of 105 Ω termination resistors for Comm5 communication links.
Details the procedure for attaching the main module to the termination module.
Provides instructions for attaching the display module to the main module.
Instructs to verify that the PC meets minimum software and hardware requirements.
Explains how to establish an EIA-232 direct connection using an RJ-12 cable and adapter.
Details how to connect the controller to a PC workstation using an RJ-11 cable and modem.
Guides on establishing an Ethernet LAN connection, including methods over existing LAN, through a hub, or direct.
Introduces troubleshooting tools like LEDs, service pin buttons, and jumpers.
Describes the function and status of various LEDs on the controller for troubleshooting.
Explains the purpose of service pin buttons (reset, Neuron ID) and the factory-use jumper.
Lists common symptoms and provides corresponding actions to resolve Tracker system problems.
Provides methods for cleaning the controller's touch screen using cloths or compressed air.
Outlines the step-by-step procedure to calibrate the touch screen for accurate input.
Lists essential supplies required for all Tracker installations.
Lists supplies that may be necessary depending on the specific Tracker installation.
Provides a table to record UCM names, locations, and 12-digit identifiers for setup.
A checklist to verify correct wiring of circuits connected to the termination board.
The official statement declaring the product's compliance with relevant standards and directives.
General| Brand | Trane |
|---|---|
| Model | Tracker Version 12 |
| Category | Air Conditioner |
| Language | English |
To Next Page
