Truma Mover XT2 - Determining the Installation Type; Measuring the Frame Height; Special Accessory Installation

24
min. 170*
min. 1350 / max. 2000
min. 80 / max. 180
min. 25
min. 35 **
140
min. 2,8
Caravan floor
Figure 7
All dimensions in mm.
* with loaded vehicle with max. permissible gross weight
** with U-profile
Measuring the frame height
A frame height of at least 140 mm is required at the level of
the tyre hub / tyre centre in the range of 320 mm from the
outer edge of the tyre.
min 320
min. 140
Figure 8
Determining the installation type
1. Standard installation
Standard installation is used with a U-profile or L-profile
chassis and a frame height of at least 140 mm. No special
accessories are required.
2. Installation on chassis with U-profile or L-profile and a
frame height of between 80 mm and less than 140 mm
In order to compensate for height, the 30mm spacer set (for
frame heights down to 110mm) or the 60mm spacer set (for
frame heights of less than 110mm down to 80mm) is required.
3. Installation on chassis with U-profiles or L-profiles
with a frame height of less than 80 mm
If the chassis has a frame height of less than 80mm, a low
chassis kit must be fitted to compensate for the height.
If a low chassis kit is used in Germany, accept-
ance by a vehicle expert is required.
4. For the AL-KO Vario III / AV chassis with a frame thickness
of less than 2.8 mm, it is essential to use the adapter kit
AL-KO Vario III / AV as a reinforcement.
5. For mounting in front of the axle on the
AL-KO chassis M, with a permissible gross weight of
up to 1800kg and adjustable beams
– 5a. In order to compensate for overlapping frame edg-
es, when the chassis is set to the minimal length the
adapterkit AL-KO M short to 1800 kg must be used.
– 5b. In order to compensate for overlapping frame edges,
the adapter kit AL-KO M to 1800kg must be used.
6. For mounting in front of the axle on the
AL-KO chassis M with a continuous frame and a
permissible gross weight of 1900 kg – 2000 kg
In order to compensate for overlapping frame edges, the
adapter kit AL-KO M 1900 - 2000 kg must be used.
7. Installation on EribaTouring chassis
The Eriba Touring adapter kit is absolutely essential for the
EribaTouring chassis.
8. Installation on EribaTouringTroll chassis
The Eriba Touring Troll adapter kit is absolutely essential for
the EribaTouring Troll chassis.
9. Installation on chassis with L-profile and with a lim-
ited amount of space
The short mounting system is required to compensate for
the height (30 or 60 mm) with substructures such as tanks.
Special accessory installation
1. Spacer kit 30 mm
For compensating for height on caravans with a frame height
of < 140 mm to 110 mm,
part no. 60030-95000.
Figure 9
2. Spacer kit 60 mm
For compensating for height on caravans with a frame height
of < 110 mm to 80 mm,
part no. 60030-95100.
Figure 10
3. Low chassis kit
For compensating for height on caravans with a frame height
of less than 80 mm and / or for bridging struts,
part no. 60010-64900.
Figure 11
If this installation kit is used in Germany, acceptance
by a vehicle expert is required.
4. Low chassis kit, short
For compensating for height on caravans with
a frame height of less than 80 mm,
part no. 60030-37600.
Figure 12
If this installation kit is used in Germany, acceptance
by a vehicle expert is required.