How to fix Tuttnauer 3870 ELVG-D printer that doesn't print anything on the paper?
If your Tuttnauer Laboratory Equipment printer prints, but nothing appears on the paper, it likely means the paper roll isn't installed correctly. Ensure you install the paper roll the right way, noting that only one side of the paper is printable.
What to do if my Tuttnauer 3870 ELVG-D Laboratory Equipment displays 'Heat Time Error'?
If your Tuttnauer Laboratory Equipment displays 'Heat Time Error', it means the system couldn't reach the required temperature in the chamber within the preset time. Try performing a new cycle. If the problem continues, call a technician.
What does 'Low Temp' mean on my Tuttnauer Laboratory Equipment?
If your Tuttnauer Laboratory Equipment displays 'Low Temp', it indicates that the temperature dropped below the sterilization temperature for more than 1 second during the sterilization cycle. Try performing a new cycle.
Why is the air detector failing in my Tuttnauer Laboratory Equipment?
If the air detector fails, consider the following possible causes: * The steam quality might not be proper. Check the steam quality and non-condensable gases. * The induced air valve might be open or leaking. Close or repair the induced air valve.
What to do if my Tuttnauer 3870 ELVG-D Laboratory Equipment printer does not print?
If the printer on your Tuttnauer Laboratory Equipment isn't printing, first ensure that the paper roll is properly inserted. If it still doesn't print and there's no obvious reason, try switching the machine off and then back on to restart it.
Why are my Tuttnauer Laboratory Equipment sterilization results unsatisfactory?
If you're experiencing unsatisfactory sterilization results, consider the following possible causes: * There might be incomplete removal of air pockets. * Sterilization conditions might involve improper temperature or pressure being too low, or the sterilization time being too short. Set the correct temperature and time according to the type and quantity of material. * Incorrect loading of the autoclave may be trapping air in the load.
What does 'RTC Error - Please Set Current Date and Time' mean on my Tuttnauer Laboratory Equipment?
If your Tuttnauer Laboratory Equipment displays 'RTC Error - Please Set Current Date and Time', it means you need to set the current date and time. If the problem persists after setting the date and time, call a technician.
What does 'Compresse d air supply error (ELVCPVG- D only)' mean on Tuttnauer 3870 ELVG-D?
If your Tuttnauer Laboratory Equipment displays 'Compresse d air supply error (ELVCPVG- D only)', it indicates a compressed air supply malfunction. Check and fix the compressed air supply.
What to do if Tuttnauer Laboratory Equipment control unit does not initialize?
If the control unit doesn't initialize, showing no display or lights on the front panel, it could be due to: * The control circuit breaker being switched off. Check and switch on the circuit breaker. * Defective power switches on the front panels of the autoclave or steam generator. Replace the defective switch.
What does 'High Pressure (Ending)' mean on my Tuttnauer 3870 ELVG-D?
If your Tuttnauer Laboratory Equipment displays 'High Pressure (Ending)', it means the system couldn't reach atmospheric pressure ± 10kPa during the ending stage. Perform a new cycle.
General safety guidelines and warnings for operating the autoclave.
Electrical specifications for 230V and 400V configurations of the autoclave.
Information on electrical power, compressed air, water, and drain requirements.
Overview of built-in safety features such as error display and relief valves.
Categorization of failures and reference to troubleshooting for error messages.
Details on the Glass sterilization program, including parameters and sequence.
Details on the Plastic sterilization program, including parameters and sequence.
Details on the Bio Hazard 1 program for bio-hazard models.
Details on the Vacuum Test program for pre-vacuum models.
Screens indicating aborted cycles after successful sterilization phase.
General description of screens displayed during a failed cycle.
Step-by-step guide on how to modify a specific parameter value.
Listing and explanation of system-wide parameters affecting all cycles.
Overview of maintenance operations to keep the autoclave functional.
Chart to help users solve minor malfunctions before contacting service.
General| Brand | Tuttnauer |
|---|---|
| Model | 3870 ELVG-D |
| Category | Laboratory Equipment |
| Language | English |
To Next Page
