Why are wraps burned after using Tuttnauer 3870EA Laboratory Equipment?
To address wraps coming out burned from your Tuttnauer Laboratory Equipment, check if the water sensor is dirty. Also, verify that the wall outlet voltage is not too high and ensure items are not touching the chamber walls or bottom. Load the autoclave according to the instructions.
What to do when my Tuttnauer Laboratory Equipment displays ‘High Temp’?
If your Tuttnauer Laboratory Equipment displays ‘High Temp’, clean the air jet and check for proper voltage at the wall outlet.
What does ‘Low Heat’ mean on my Tuttnauer Laboratory Equipment?
If the message ‘Low Heat’ is displayed during heat up on your Tuttnauer Laboratory Equipment, it indicates a bad temperature sensor. If heating elements are remaining on instead of cycling on and off, call for a technician.
How to clean a very dirty chamber in my Tuttnauer Laboratory Equipment?
If the chamber of your Tuttnauer Laboratory Equipment is very dirty, use Chamber Brite ™ to clean the autoclave; very dirty machines may require two cleanings.
Why are instruments rusting in my Tuttnauer 3870EA?
If instruments are rusting after sterilization in your Tuttnauer Laboratory Equipment, first determine if it's true rust by using a pencil eraser to remove the brown spot. If there is no pitting, the instrument is just dirty. Use distilled water for sterilizing and ensure dissimilar metals are not in contact with each other.
Why does Tuttnauer Laboratory Equipment printer feed paper constantly?
If the printer on your Tuttnauer Laboratory Equipment gives paper feeds all the time when the machine is switched on, make sure the ‘feed button’ on the printer is not stuck.
What to do if the keyboard of my Tuttnauer 3870EA Laboratory Equipment does not respond?
If the keyboard of your Tuttnauer Laboratory Equipment does not respond, press the STOP key for 2 seconds to abort any program that may still be running.
How to troubleshoot a Tuttnauer 3870EA system that shows no response when turned on?
If your Tuttnauer Laboratory Equipment does not respond when you turn it on, try the following: First, check and fix all connections. If the issue persists, replace any faulty cables, connectors, or the power switch.
Why is my Tuttnauer 3870EA making a loud noise?
If you hear a loud noise coming from the reservoir of your Tuttnauer Laboratory Equipment, the sterilization temperature may be set too high. The maximum setting is 274ºF (134ºC).
How to clean a very dirty Tuttnauer Laboratory Equipment chamber?
To clean a very dirty chamber in your Tuttnauer Laboratory Equipment, use Chamber Brite ™. Very dirty machines may require two cleanings.
Inspect the autoclave upon arrival for any shipping damage.
Details the functions of each key on the control panel and program selection.
Details error messages, warnings, and safety precautions displayed by the unit.
Instructions and parameters for sterilizing unwrapped instruments.
Parameters and procedure for sterilizing wrapped items and porous loads.
Specific program settings for sterilizing glassware.
Guidelines for electrical connection and safety precautions.
Safety instructions for moving the autoclave.
Pre-sterilization cleaning and preparation of instruments.
Use of indicators and spore tests for sterilization assurance.
Steps for initial operation and setup before first use.
Overview of routine maintenance tasks to keep the autoclave in good working order.
Solutions for when the autoclave does not power on or respond.
Troubleshooting steps for the 'Low Heat' error message.
Solutions for the 'Low Water' error message.
Troubleshooting steps for the 'Low Pressure' error message.
Solutions for the 'Low Temperature' error message.
Troubleshooting steps for the 'High Temperature' error message.
Solutions for the 'High Pressure' error message.
Solutions for leaks occurring at the autoclave door.
Steps to clear a clogged drain in the autoclave.
Troubleshooting issues with sterilization indicators.
Solutions for wrapped items not drying properly.
General| Frequency | 50/60 Hz |
|---|---|
| Power Supply | 120V or 230V |
| Temperature Range | 105°C to 137°C |
| Control System | Microprocessor control |
| Trays Capacity | 3 |
| Voltage | 220-240 V |
| Operating Temperature | 5°C to 40°C |
| Chamber Volume | 85 liters |
To Next Page
