Why is my Tuttnauer 3870EA Laboratory Equipment leaking at the door?
If your Tuttnauer Laboratory Equipment is leaking at the door, ensure the door is tightened enough and the door gasket is sealing the chamber. If necessary, replace the door gasket.
Why are wraps burned after using Tuttnauer 3870EA Laboratory Equipment?
To address wraps coming out burned from your Tuttnauer Laboratory Equipment, check if the water sensor is dirty. Also, verify that the wall outlet voltage is not too high and ensure items are not touching the chamber walls or bottom. Load the autoclave according to the instructions.
How to clean a very dirty Tuttnauer Laboratory Equipment chamber?
To clean a very dirty chamber in your Tuttnauer Laboratory Equipment, use Chamber Brite ™. Very dirty machines may require two cleanings.
Why does Tuttnauer Laboratory Equipment take so long to heat up?
If your Tuttnauer Laboratory Equipment takes too long to heat up, clean the air jet and check for proper voltage at the wall outlet.
What to do if spore tests fail in Tuttnauer Laboratory Equipment?
If spore tests are failing or indicator strips are not turning in your Tuttnauer Laboratory Equipment, clean the air jet. Also, make sure the sterilization time and temperature are set correctly, and ensure the autoclave is not too heavily loaded.
Why does Tuttnauer Laboratory Equipment printer feed paper constantly?
If the printer on your Tuttnauer Laboratory Equipment gives paper feeds all the time when the machine is switched on, make sure the ‘feed button’ on the printer is not stuck.
How to troubleshoot Tuttnauer 3870EA machine not responding?
If your Tuttnauer Laboratory Equipment machine isn't responding, verify that the main switch is in the ‘On’ position, the power cord is properly connected to both the machine and the mains, and the circuit breaker hasn't tripped. Also, check the reset button on the cut-out thermostat.
What to do if Tuttnauer 3870EA Laboratory Equipment process fails during heating stage with a HIGH TEMP message?
If your Tuttnauer Laboratory Equipment process fails while initiating the heating stage and displays a HIGH TEMP message, try changing the setting of the thermostat.
How to clean a very dirty chamber in my Tuttnauer Laboratory Equipment?
If the chamber of your Tuttnauer Laboratory Equipment is very dirty, use Chamber Brite ™ to clean the autoclave; very dirty machines may require two cleanings.
What does ‘Low Heat’ mean on my Tuttnauer Laboratory Equipment?
If the message ‘Low Heat’ is displayed during heat up on your Tuttnauer Laboratory Equipment, it indicates a bad temperature sensor. If heating elements are remaining on instead of cycling on and off, call for a technician.
Inspect the autoclave upon arrival for any shipping damage.
Details the functions of each key on the control panel and program selection.
Details error messages, warnings, and safety precautions displayed by the unit.
Instructions and parameters for sterilizing unwrapped instruments.
Parameters and procedure for sterilizing wrapped items and porous loads.
Specific program settings for sterilizing glassware.
Guidelines for electrical connection and safety precautions.
Safety instructions for moving the autoclave.
Pre-sterilization cleaning and preparation of instruments.
Use of indicators and spore tests for sterilization assurance.
Steps for initial operation and setup before first use.
Overview of routine maintenance tasks to keep the autoclave in good working order.
Solutions for when the autoclave does not power on or respond.
Troubleshooting steps for the 'Low Heat' error message.
Solutions for the 'Low Water' error message.
Troubleshooting steps for the 'Low Pressure' error message.
Solutions for the 'Low Temperature' error message.
Troubleshooting steps for the 'High Temperature' error message.
Solutions for the 'High Pressure' error message.
Solutions for leaks occurring at the autoclave door.
Steps to clear a clogged drain in the autoclave.
Troubleshooting issues with sterilization indicators.
Solutions for wrapped items not drying properly.
General| Frequency | 50/60 Hz |
|---|---|
| Power Supply | 120V or 230V |
| Temperature Range | 105°C to 137°C |
| Control System | Microprocessor control |
| Trays Capacity | 3 |
| Voltage | 220-240 V |
| Operating Temperature | 5°C to 40°C |
| Chamber Volume | 85 liters |
To Next Page
