What does ‘Low Heat’ mean on my Tuttnauer Laboratory Equipment?
If the message ‘Low Heat’ is displayed during heat up on your Tuttnauer Laboratory Equipment, it indicates a bad temperature sensor. If heating elements are remaining on instead of cycling on and off, call for a technician.
How to clean a very dirty chamber in my Tuttnauer Laboratory Equipment?
If the chamber of your Tuttnauer Laboratory Equipment is very dirty, use Chamber Brite ™ to clean the autoclave; very dirty machines may require two cleanings.
What to do if Tuttnauer 3870EA Laboratory Equipment process fails during heating stage with a HIGH TEMP message?
If your Tuttnauer Laboratory Equipment process fails while initiating the heating stage and displays a HIGH TEMP message, try changing the setting of the thermostat.
How to troubleshoot Tuttnauer 3870EA machine not responding?
If your Tuttnauer Laboratory Equipment machine isn't responding, verify that the main switch is in the ‘On’ position, the power cord is properly connected to both the machine and the mains, and the circuit breaker hasn't tripped. Also, check the reset button on the cut-out thermostat.
What should I do if my Tuttnauer Laboratory Equipment shows ‘Low Pres’?
If the 'Low Pres' message is displayed on your Tuttnauer Laboratory Equipment, clean the water level electrode inside the vessel. Also, ensure the door is fully closed, the door gasket is properly seated, and there is no steam leakage. Check the leveling of the machine.
How to fix ‘High Pres’ error on Tuttnauer 3870EA Laboratory Equipment?
If the 'High Pres' message appears on your Tuttnauer Laboratory Equipment, the air jet might be clogged; clean it. It could also mean that the heating elements are continuously on, or the temperature sensor is faulty. In these cases, contact a technician.
How to unclog the drain on Tuttnauer 3870EA Laboratory Equipment?
If the drain of your Tuttnauer Laboratory Equipment is clogged: 1. Open the drain by turning it counterclockwise and place a heavy object over the reservoir cover. 2. Blow compressed air into the drain to force debris back into the reservoir, then clean out the reservoir. 3. Alternatively, disassemble the drain valve, clean it, and blow out the line. Reassemble the valve, ensuring the large 'O' ring is properly seated.
What should I do if my Tuttnauer Laboratory Equipment displays ‘High Pres’?
If your Tuttnauer Laboratory Equipment displays ‘High Pres’, clean the air jet. Ensure the sterilization time and temperature are set correctly; if unsure, use the default settings. Also, make sure the autoclave is not too heavily loaded.
What to do if my Tuttnauer 3870EA is not responding?
If your Tuttnauer Laboratory Equipment is not responding, ensure the main switch is in the ‘On’ position. Also, verify the power cord is properly connected to both the machine and the mains. Check the reset button on the cut-out thermostat and make sure the circuit breaker hasn't tripped; lift the circuit breaker lever if it has.
Why is my Tuttnauer 3870EA Laboratory Equipment leaking at the door?
If your Tuttnauer Laboratory Equipment is leaking at the door, ensure the door is tightened enough and the door gasket is sealing the chamber. If necessary, replace the door gasket.
Inspect the autoclave upon arrival for any shipping damage.
Details the functions of each key on the control panel and program selection.
Details error messages, warnings, and safety precautions displayed by the unit.
Instructions and parameters for sterilizing unwrapped instruments.
Parameters and procedure for sterilizing wrapped items and porous loads.
Specific program settings for sterilizing glassware.
Guidelines for electrical connection and safety precautions.
Safety instructions for moving the autoclave.
Pre-sterilization cleaning and preparation of instruments.
Use of indicators and spore tests for sterilization assurance.
Steps for initial operation and setup before first use.
Overview of routine maintenance tasks to keep the autoclave in good working order.
Solutions for when the autoclave does not power on or respond.
Troubleshooting steps for the 'Low Heat' error message.
Solutions for the 'Low Water' error message.
Troubleshooting steps for the 'Low Pressure' error message.
Solutions for the 'Low Temperature' error message.
Troubleshooting steps for the 'High Temperature' error message.
Solutions for the 'High Pressure' error message.
Solutions for leaks occurring at the autoclave door.
Steps to clear a clogged drain in the autoclave.
Troubleshooting issues with sterilization indicators.
Solutions for wrapped items not drying properly.
General| Frequency | 50/60 Hz |
|---|---|
| Power Supply | 120V or 230V |
| Temperature Range | 105°C to 137°C |
| Control System | Microprocessor control |
| Trays Capacity | 3 |
| Voltage | 220-240 V |
| Operating Temperature | 5°C to 40°C |
| Chamber Volume | 85 liters |
To Next Page
