Tuttnauer 3850 M - Service Manual

Other manuals for Tuttnauer 3850 M

Technician Manual51 pages

Questions and Answers

E
ejacksonAug 14, 2025
How to troubleshoot a Tuttnauer Laboratory Equipment when the POWER indicator light doesn't turn on?
- R
  Randy MorganAug 14, 2025
  If the POWER indicator light on your Tuttnauer Laboratory Equipment does not light up, several issues could be the cause. First, the main switch might be defective, in which case you should check and replace it if necessary. It could also be a problem with the "POWER" bulb itself, so try replacing it. Inspect the line from the entry point to the main switch for any damage and repair it. Another potential issue is an internal electrical problem within the unit, which requires further investigation. Additionally, the “Power” light may need to be replaced.
D
Daniel FloresAug 18, 2025
What to do if steam escapes from the safety valve of my Tuttnauer 3850 M Laboratory Equipment?
- P
  Peter LyonsAug 18, 2025
  If steam is escaping from the safety valve of your Tuttnauer Laboratory Equipment, activate the safety valve. If the leaking continues after activation, you will need to replace the safety valve.
I
iparkerAug 21, 2025
Why won't water enter the chamber of my Tuttnauer 3850 M Laboratory Equipment?
- D
  Desiree FarmerAug 21, 2025
  If water is not entering the chamber of your Tuttnauer Laboratory Equipment, it could be due to a clog in the multi-purpose valve or the pipe. Follow instructions in para. 6.10 to resolve this issue.
A
Alexander BennettAug 25, 2025
What to do if the door handle of my Tuttnauer Laboratory Equipment won't turn to open?
- D
  danawhiteAug 25, 2025
  If the door handle of your Tuttnauer Laboratory Equipment cannot be turned counter-clockwise to open, it may be because the door pin is set in a groove. Try turning the handle slightly in the closing direction (clockwise) and then attempt to open it again. If the problem persists, the door locking system may be stuck or the bellows damaged. Refer to “Pressure Door Lock System”. After opening the door, replace the bellows.
C
Carolyn WilsonAug 27, 2025
Why is the 'HEAT' light off and there's no heating in my Tuttnauer Laboratory Equipment?
- A
  anna79Aug 27, 2025
  If the “HEAT” light is not on and there is no heating in your Tuttnauer Laboratory Equipment, the faulty thermostat (B10) should be fixed or replaced.
A
andrewromanAug 31, 2025
Why is the 'HEAT' light off and heating insufficient in my Tuttnauer Laboratory Equipment?
- C
  Colton CortezAug 31, 2025
  If the “HEAT” light is not on and the heating is insufficient in your Tuttnauer Laboratory Equipment, the faulty thermostat (B10) should be fixed or replaced.
C
Crystal MurphySep 3, 2025
Why is the 'HEAT' light off, but my Tuttnauer 3850 M still operates?
- J
  James CameronSep 3, 2025
  If the “HEAT” light is not on but the autoclave operates in your Tuttnauer Laboratory Equipment, the faulty thermostat (B10) should be fixed or replaced.
J
Jorge WebbSep 6, 2025
Why does the multi-purpose valve on my Tuttnauer Laboratory Equipment turn backwards?
- B
  brittanycampbellSep 6, 2025
  If the multi-purpose valve on your Tuttnauer Laboratory Equipment turns backwards, the internal spring in the multi-purpose valve has likely broken. Replace the multi-purpose valve.
J
Jared AtkinsSep 10, 2025
What causes the timer on my Tuttnauer Laboratory Equipment to not time down?
- A
  Alexander DonaldsonSep 12, 2025
  If the timer on your Tuttnauer Laboratory Equipment does not time down, the internal gearing has likely worn down. Replace the timer.