What to do if 'Low Vacuum' is displayed on Tuttnauer Laboratory Equipment?
If the Tuttnauer Laboratory Equipment displays 'Low Vacuum', this indicates that a vacuum level of 15kPa was not reached within 20 minutes after the cycle started during the air removal stage. To resolve this, try performing a new cycle. If the issue persists, it may be necessary to call a technician, or the bio-hazard filter may be clogged.
What does 'Supplied Distilled Water Error' mean on Tuttnauer 3850 ELV Laboratory Equipment?
If the Tuttnauer Laboratory Equipment displays the message "Supplied Distilled Water Error", it means the mineral-free water reservoir is empty. To fix this, simply fill the mineral-free water reservoir.
What to do if Tuttnauer Laboratory Equipment displays 'No Water'?
If the Tuttnauer Laboratory Equipment displays 'No Water', first check and fix the mineral-free water supply. Then, inspect and clean the water inlet filter, and finally, clean the water level electrode.
What to do when Tuttnauer Laboratory Equipment displays 'Cycle counter exceeded -'?
If the Tuttnauer Laboratory Equipment displays 'Cycle counter exceeded -', call for service. This is because the number of cycles since the last periodical maintenance has exceeded the preset number.
What to do if Tuttnauer Laboratory Equipment displays 'Cycle Failed'?
If the Tuttnauer Laboratory Equipment displays 'Cycle Failed', perform a new cycle.
How to troubleshoot a Tuttnauer 3850 ELV Laboratory Equipment when the display is not activated?
If the display of your Tuttnauer Laboratory Equipment is not activated, first, check the power source to ensure it meets the required specifications. Next, verify that the ON/OFF switch is in the ‘On’ position. Also, make sure the power cord is properly connected to both the machine and the mains. Check the reset button on the cut-out thermostat and reset it if necessary. Finally, check if the circuit breaker has tripped and reset it if needed.
What to do if my Tuttnauer 3850 ELV Laboratory Equipment is leaking at the door?
If your Tuttnauer Laboratory Equipment is leaking at the door, ensure that the door is tightened sufficiently. If the leakage persists, consider replacing the door gasket.
How to troubleshoot a Tuttnauer 3850 ELV Laboratory Equipment machine that is not responding?
If the Tuttnauer Laboratory Equipment machine isn't responding, first ensure the main switch is in the ‘On’ position. Then, check that the power cord is properly connected to both the machine and the mains. Finally, lift the circuit breaker lever if it has tripped. These issues may be caused by the main switch being off, a disconnected power cord, or a tripped circuit breaker.
What to do if my Tuttnauer 3850 ELV printer does not print?
If the Tuttnauer Laboratory Equipment printer isn't printing, make sure the paper roll is correctly inserted. If there's still no printing, switch the machine off and then back on to restart it. This could be happening because no paper is inserted or for no obvious reason.
Why is my Tuttnauer Laboratory Equipment leaking at the door?
If the Tuttnauer Laboratory Equipment is leaking at the door, the door gasket may be dirty or damaged. Try cleaning the door gasket. If the leaking continues, call for service.
Key safety guidelines for operation, personnel, and materials.
Details standards, electrical data, and technical specifications.
Explains the operational stages like air removal, heat, and sterilization.
Details the control panel components and their functions.
Lists and describes the available sterilization programs.
Procedures for opening, closing, starting, and unloading the cycle.
Routine maintenance tasks for daily, weekly, and periodic checks.
General| Type | Autoclave |
|---|---|
| Model | 3850 ELV |
| Number of Trays | 3 |
| Frequency | 50/60 Hz |
| Power Consumption | 3 kW |
| Weight | 150 kg |
| Control System | Microprocessor |
| Display | LCD |
| Printing Option | Optional |
| Power | 3000W |
| Voltage | 220-240V |
| Temperature Range | 105 to 137 °C |
| Operating Pressure | 2.1 bar |
| Power Supply | Single Phase |
| Water Supply | Automatic |
| Drainage | Automatic |
| Sterilization Pressure Range | 0.22-0.35 MPa |
| Chamber Volume | 85 liters |
To Next Page