Name: Unitech MS842P
Brand: Unitech
Rating: 5 (1 reviews)

To Next Page

To Previous Page

Code 39 Full ASCII Conversion

Code 39 Full ASCII is a variant of Code 39, which pairs characters to encode the

full ASCII character set. To enable or disable Code 39 Full ASCII, scan the

appropriate bar code below.

Note:

You cannot enable Trioptic Code 39 and Code 39 Full ASCII simultaneously.

Code 39 Full ASCII to Full ASCII Correlation is host-

dependent, and is therefore

described in the ASCII Character Set Table for the appropriate interface. See the

section -- ASCII Character Set for USB -- or the section --

ASCII Character Set for

Serial Hosts.

Set Lengths for Code 39

The length of a code refers to the number of characters (i.e., human readable

characters), including check digit(s) the code contains. Set lengths for Code 39 to

any length, one or two discrete lengths, or lengths within a specific range. If Code

39 Full ASCII is enabled, Length Within a Range or Any Length are the preferred

options.

Note: When setting lengths for different bar code types, enter a leading zero for

single digit numbers.



One Discrete Length - Select this option to decode only Code 39 symbols

containing a selected length. Select the length using the numeric bar codes in the

appendix of Numeric Bar Codes. For example, to decode only Code 39 symbols

with 14 characters, scan Code 39 – One Discrete Length, and then scan 1

followed by 4. To correct an error or change the selection, scan the Cancel bar

code.



Two Discrete Lengths - Select this option to decode only Code 39 symbols

containing either of two selected lengths. Select lengths using the numeric bar

codes in the appendix of Numeric Bar Codes. For example, to decode only Code

39 symbols containing either 2 or 14 characters, select Code 39 – Two Discrete

Lengths, and then scan 0, 2, 1, and then 4. To correct an error or change the

selection, scan the Cancel bar code.



Length Within Range - Select this option to decode a Code 39 symbol with a

specific length range. Select lengths using numeric bar codes in the appendix of

Numeric Bar Codes. For example, to decode Code 39 symbols containing between

4 and 12 characters, first scan Code 39 – Length Within Range. Then scan 0, 4, 1,

and 2 (enter a leading zero for single digit numbers). To correct an error or change

the selection, scan the Cancel bar code.



Any Length - Select this option to decode Code 39 symbols containing any

number of characters within the decoder’s capability.

Other manuals for Unitech MS842P

Quick Start Guide2 pages

Questions and Answers:

Need help?

Do you have a question about the Unitech MS842P and is the answer not in the manual?

Unitech MS842P Specifications

General

Type	Handheld bar code reader
Sensor type	CMOS
Scanner type	1D/2D
Tilt reading angle	-60 - 60 °
Linear (1D) barcodes supported	Codabar, Code 11, Code 128, Code 25 (IR 2 of 5), Code 39, Code 93, EAN-13, GS1-128 (UCC/EAN-128), JAN, MSI, Telepen, Trioptic, U.P.C.
2D (matrix & stacked) barcodes supported	Aztec Code, Composite Codes, Data Matrix, MaxiCode, Micro QR Code, PDF417, QR Code, TLC-39
USB version	2.0
Wireless range	10 m
Operating frequency	2400 MHz
Standard interfaces	Bluetooth, USB
Connectivity technology	Wired & Wireless
Certification	CE, FCC, BSMI, VCCI
Product color	Black, Grey, Yellow
Housing material	-
International Protection (IP) code	IP54
Battery life	10 h
Charging time	4 h
Input voltage	5 V
Battery capacity	1620 mAh
Power consumption	400 mA
Power source type	DC
Storage temperature (T-T)	-30 - 70 °C
Operating temperature (T-T)	0 - 50 °C
Operating relative humidity (H-H)	5 - 95 %