Need help?Do you have a question about the Unitech MS836 and is the answer not in the manual?
General| Type | Handheld bar code reader |
|---|---|
| Wavelength | 650 nm |
| Sensor type | Laser |
| Scanner type | 1D |
| Read rate (max) | 100 reads/s |
| Maximum scan area | 220 x 250 mm |
| Maximum scan width | 220 mm |
| Linear (1D) barcodes supported | Codabar, Code 128, Code 39, EAN-13, EAN-8, GS1-128 (UCC/EAN-128), Interleaved 2 of 5, MSI, U.P.C. |
| 2D (matrix & stacked) barcodes supported | Not supported |
| Standard interfaces | USB |
| Connectivity technology | Wired |
| Power consumption | 85 mA |
| Buzzer | Yes |
| Certification | CE, FCC |
| Product color | Black |
| Housing material | Plastic |
| International Protection (IP) code | IP42 |
| Storage temperature (T-T) | -20 - 60 °C |
| Operating temperature (T-T) | 0 - 45 °C |
| Operating relative humidity (H-H) | 5 - 85 % |
Weight and Dimensions| Depth | 95 mm |
|---|---|
| Width | 70 mm |
| Height | 160 mm |
| Weight | 150 g |
Control scanner programming mode access using specific barcodes.
Barcodes used to configure scanner settings and operations.
Restore scanner to its original factory settings and configurations.
Defines how the scanner activates a decode session.
Sets the maximum duration of a single decode session.
Scanner scans at user-specified intervals, not triggered by a manual pull.
Sets the delay between consecutive decode sessions.
Time before scanner can read the same barcode again.
Scanner activates decode session upon detecting ambient illumination changes.
Timeout before activating decode session after illumination change.
Controls whether the scanner can reread the same barcode.
Adjusts scanner's response to ambient illumination changes.
Decode session activated by a host command rather than trigger.
Specifies number of retries for barcode decoding.
Controls audible feedback for successful scans.
Enables or disables notification of decoded results.
Controls scanner illumination behavior during scanning.
Temporary parameter settings that reset on power cycle.
Configuration for serial communication via RS-232.
Sets data transmission speed for serial communication.
Configures error checking for serial data transmission.
Defines the number of stop bits for serial communication.
Specifies data bits per character in serial communication.
Configuration options for USB connectivity.
Emulates keyboard input for ASCII characters via keypad.
Maps function characters to specific key sequences.
Selects keyboard layout for USB connection.
Allows conversion of scanned data to different cases.
Controls numeric keypad emulation for scanned numbers.
Simulates a serial port for USB data transfer.
Protocol for direct data communication via USB.
Recommended interface for new applications via USB.
Configuration for PS/2 keyboard interface.
Defines the order of prefix elements in scanned data.
Options for adding prefixes to scanned data.
Options for adding suffixes to scanned data.
Controls whether check digits are transmitted with scanned data.
Sets minimum and maximum length for barcode decoding.
Verifies data integrity using check digits for various symbologies.
Configures how add-on codes are handled for EAN/UPC barcodes.
Controls transmission of system characters for UPC-E barcodes.
Controls transmission of start/stop characters for symbologies.
Sets the format for ISBN barcode interpretation.
Controls transmission of preamble characters for UPC-A barcodes.
General settings for enabling/disabling symbologies.
Configuration for Code 128 barcode symbology.
Configuration for UCC/EAN-128 barcode symbology.
Configuration for AIM 128 barcode symbology.
Configuration for EAN-8 barcode symbology.
Configuration for Interleaved 2 of 5 barcode symbology.
Configuration for Industrial 25 barcode symbology.
Configuration for Standard 25 barcode symbology.
Configuration for Code 39 barcode symbology.
Configuration for Codabar barcode symbology.
Configuration for Code 11 barcode symbology.
Configuration for Plessey barcode symbology.
Configuration for MSI-Plessey barcode symbology.
Configuration for EAN-13 barcode symbology.
Comprehensive table of all scanner parameters and their default settings.
Table mapping symbologies to their AIM IDs.
Reference for ASCII character codes and their representations.
Barcodes representing numeric digits 0-9 for programming.
Barcodes used to save or cancel programming entries.
To Next Page
