Home
Unitronics
Gateway
GW-BAC1
Unitronics GW-BAC1 User Manual
4
of 1
of 1 rating
28 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
Unitronics’s
BACnet Gate
way User Guide
Page
13
of
28
Unitronics
Configuration file c
reation steps
BACnet Connection:
Use this menu for s
etting up the BACn
et Gateway communication p
arameters.
First you must choose the t
ype of BACnet Protocol
: MS/TP (Serial) or IP
.
Figure
11
:
BACnet Connection MS/TP Screen
Figure
12
:
BACnet Connection IP Sc
reen
12
14
Table of Contents
Default Chapter
1
User Guide
1
Table of Contents
3
1 Introduction
5
GW-BAC1 Gateway
5
Record Identification Data
5
Technical Support
5
2 Interfacing GW-BAC1 to Devices
6
GW-BAC1 Showing Connection Ports
6
Figure 1: Bacnet Board
6
Connecting a Unitronics PLC to the GW-BAC1 Via Modbus RS-485
7
Figure 2: Power and RS-485 Connections
7
2.2.1 Biasing the Modbus RS-485 Network
8
Figure 3: Modbus RS-485 Biasing Switch on the GW-BAC1
8
2.2.2 End of Line Termination Switch for the Modbus RS -485 Port on the GW-BAC1
9
Figure 4: Modbus RS-485 End-Of-Line Termination Switch on the GW-BAC1
9
Bacnet MS/TP Field Devices: Wiring Field Port to RS-485 Network
10
Figure 5: Connection from GW-BAC1 to RS-485 Field Network
10
Figure 6: RS-485 EOL Switch
10
Connecting Power to GW-BAC1
11
Figure 7: Required Current Draw for the GW-BAC1
11
Figure 8: Power Connections
11
3 Creating Configuration File and Configurating the PLC
12
Unibacnet Configurator
12
Figure 9: Tools Menu on Visilogic
12
Figure 10: Tools Menu on Unilogic
12
Figure 11: Bacnet Connection MS/TP Screen
13
Figure 12: Bacnet Connection IP Screen
13
Figure 13: Bacnet Nodes Screen
14
Figure 14: Bacnet Map Descriptors Screen
14
Figure 15: Modbus Connection RTU Screen
15
Figure 16: Modbus Connection IP Screen
15
Figure 17: Finish Screen
16
Figure 18: File Transfer Screen
17
Figure 19: File Menu
17
PLC Configuration Example
18
Figure 20: MODBUS RTU Configuration
18
Figure 21: Example of COM Initialize
18
Figure 22: Example of Modbus Configuration
19
Figure 23: Example of MODBUS TCP/IP Configurator
19
Figure 24: Example of TCP/IP Card and Socket Initialize
19
Figure 25: Example of TCP/IP Card and Socket Initialize
20
Figure 26: Example of MODBUS Command
20
4 Changing the GW-BAC1 IP Address
21
Connect the PC to GW-BAC1 Via the Ethernet Port
21
Figure 27: Ethernet Port Location
21
Figure 28: PC IP Configuration
21
Bacnet/Ip: Setting IP Address for Field Network
22
Figure 29: Changing IP Address Via FST Web GUI
22
Appendix A. Troubleshooting
23
Appendix A.1. Check Wiring and Settings
23
Appendix A.2. Diagnostic Capture
24
Figure 30: Ethernet Port Location
24
Figure 31: Diagnostic Tool - Device Selection
24
Figure 32: Diagnostic Selection
25
Figure 33: Diagnostic Tool - Start Diagnostic
25
Figure 34: Diagnostic Tool -Diagnostic Test Complete
26
Appendix A.3. LED Diagnostics for Modbus RTU Communications between GW-BAC1 and Devices
27
Figure 35: Diagnostic Leds
27
Appendix B. Reference
28
Appendix B.1. Specifications
28
Appendix B.2. Compliance with UL Regulations
28
Figure 36: Specifications
28
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Unitronics GW-BAC1 and is the answer not in the manual?
Ask a question
Unitronics GW-BAC1 Specifications
General
Brand
Unitronics
Model
GW-BAC1
Category
Gateway
Language
English
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General