Utax CD 5130 - User Manual

Questions and Answers

D
davidharrisSep 6, 2025
Why is the top edge of the paper dirty after printing with my Utax All in One Printer?
- M
  Meagan HarrisSep 7, 2025
  If the top edge or back of the paper is dirty after printing with your Utax All in One Printer, the inside of the machine might be dirty. Clean the inside of the machine.
C
Crystal DavisAug 22, 2025
Why are my Utax All in One Printer printouts too light?
- N
  nhowellAug 22, 2025
  If your Utax All in One Printer's printouts are too light, several factors could be the cause. The printer might be in Manual Density mode, requiring you to select the correct density level. The toner may not be evenly distributed; try shaking the toner container from side to side several times. You might need to replace the toner container if there's a message indicating it's low. Damp paper can also cause this issue, so try replacing it with new paper. Finally, check if EcoPrint mode is enabled and, if so, disable it.
A
Allen WilliamsSep 3, 2025
How to fix Utax All in One Printer when it cannot feed originals?
- A
  Adam HayesSep 3, 2025
  If your Utax All in One Printer cannot feed originals, make sure the originals are placed correctly in the document processor. Align the original width guides securely before placing the originals.
H
hartmelissaSep 2, 2025
Why are my Utax All in One Printer printouts fuzzy?
- M
  Melissa GuzmanSep 2, 2025
  If your Utax All in One Printer's printouts are fuzzy, it might be due to high humidity. Try using the machine in a location with suitable humidity.
K
Katie GonzalezSep 1, 2025
How to remove vertical streaks on Utax All in One Printer prints?
- T
  terryandreaSep 1, 2025
  If vertical streaks appear on prints from your Utax All in One Printer, the slit glass may be dirty. Clean the slit glass to resolve this issue.
L
Lindsey HarrisAug 30, 2025
What to do if pressing Start key on Utax All in One Printer does not produce copies?
- D
  Darius BeckerAug 30, 2025
  If pressing the Start key on your Utax All in One Printer does not produce copies, first check the Message Display for any messages and respond accordingly. Also, if the machine is in Sleep mode, press any key on the operation panel to wake it up; it should be ready to copy within 15 seconds.
D
Dakota FitzgeraldAug 29, 2025
Why are printouts from my Utax All in One Printer wrinkled or curled?
- B
  brandi23Aug 29, 2025
  If the printouts from your Utax All in One Printer are wrinkled or curled, the paper might be damp. Try replacing the paper with new paper.
R
Ryan CruzAug 27, 2025
How to clean Utax All in One Printer dirty printouts?
- T
  Teresa SantosAug 28, 2025
  If your Utax All in One Printer is producing dirty printouts, the platen or the document processor might be dirty. Clean the platen or the document processor to resolve this issue.
M
Michael LoganAug 27, 2025
Why Utax All in One Printer ejects blank sheets?
- H
  Hector CarrAug 27, 2025
  If your Utax All in One Printer is ejecting blank sheets, check how the originals are loaded. When using the platen, place originals face-down and align them with the slit glass. When using the document processor, place originals face-up.
K
Kimberly WarrenAug 25, 2025
Why my Utax All in One Printer cannot print?
- O
  Olivia RangelAug 26, 2025
  If your Utax All in One Printer is unable to print, check a few things. Ensure the power cord is plugged into an AC outlet and that the power switch is turned on. Verify the printer cable is securely connected. If the machine was powered on before connecting the printer cable, power it on again after connecting the cable. Check if the print job is paused and, if so, press [Resume]. Finally, if an error message is displayed, follow the corresponding procedure.