Utax CD 1325 - User Manual

Questions and Answers

K
Katherine CopelandAug 17, 2025
Why are my Utax CD 1325 All in One Printer printouts too light?
- P
  Paul NobleAug 17, 2025
  If your Utax All in One Printer is producing printouts that are too light, there are several potential causes. First, if the machine is in Auto Density mode, ensure the correct density level is set. If it's in Manual Density mode, use the Image Quality settings to adjust the density level. Also, make sure the toner is distributed evenly by shaking the toner container from side to side about 5 times. Check if there's a message indicating the need for more toner; if so, replace the toner container. Lastly, if the paper is damp, replace it with new paper.
D
dmorenoAug 20, 2025
Why does my Utax CD 1325 All in One Printer paper often jam?
- D
  danny83Aug 20, 2025
  If your Utax All in One Printer is experiencing frequent paper jams, several factors could be the cause. Ensure that the paper is loaded correctly. If the paper is of a supported type and in good condition, try removing it, turning it over, and reloading it. Replace the paper if it is curled, folded, or wrinkled. Also, check for and remove any loose scraps or jammed paper inside the machine.
J
John AllenAug 22, 2025
Why are the printouts from my Utax CD 1325 All in One Printer too dark?
- S
  Scott ParkerAug 22, 2025
  If your Utax All in One Printer is producing printouts that are too dark, and the machine is in Auto Density mode, set the correct density level. Alternatively, if your machine is in Manual Density mode, use the Image Quality settings to set the correct density level.
J
James CuevasAug 25, 2025
What to do if my Utax CD 1325 cannot print?
- R
  Robert ColemanAug 26, 2025
  If your Utax All in One Printer is not printing, first, ensure that the power cord is plugged into an AC outlet. Next, verify that the main power switch is turned on. Check that the printer cable is securely connected. If the machine was powered on before connecting the printer cable, power it on again after connecting the cable. Finally, if 'Press Status Key...' is displayed, press the Status/Job Cancel key, select [Printing Jobs], and then choose [Resume All Print Jobs] to restart printing.
M
Michael JeffersonAug 27, 2025
How to fix black lines on Utax CD 1325 printouts from document processor?
- M
  Mark VasquezAug 27, 2025
  If the printouts from your Utax All in One Printer's document processor have black lines, the slit glass may be dirty. Clean the slit glass to resolve this issue.
B
brownmistyAug 30, 2025
What to do if Utax CD 1325 operation panel keys locked up?
- T
  Tara BarkerAug 30, 2025
  If the operation panel of your Utax All in One Printer locks up and the keys do not respond, the panel may be locked. Check the panel lock setting in COMMAND CENTER and change the setting if necessary.
T
Thomas AndersonSep 1, 2025
Why are images skewed on my Utax All in One Printer?
- C
  Christopher ClarkSep 1, 2025
  If the images from your Utax All in One Printer are skewed, make sure the originals are placed correctly, aligning them with the original size indicator plates when using the platen. Also, check the position of the paper width guides to ensure the paper is loaded correctly.
D
Daniel SmithSep 4, 2025
Why are my Utax CD 1325 All in One Printer printouts wrinkled?
- K
  Kimberly ButlerSep 4, 2025
  If the printouts from your Utax All in One Printer are wrinkled, the paper separator of the paper feed unit may be dirty. Clean the paper separator.
M
Megan RhodesSep 6, 2025
Why are the printouts from my Utax All in One Printer not clear?
- C
  Carrie PayneSep 7, 2025
  If your Utax All in One Printer's printouts are not clear, it might be due to the image quality setting. Select the appropriate image quality setting for the original document.
J
Jessica HowellSep 9, 2025
Why does my Utax CD 1325 All in One Printer eject blank sheets?
- A
  anadavisSep 9, 2025
  If your Utax All in One Printer ejects blank sheets, ensure the originals are loaded correctly. When placing originals on the platen, place them face-down and align them with the original size indicator plates. When using the optional document processor, place the originals face-up.

Summary

1 Copying Functions

Original Size

Specifies the size of originals for scanning or copying.

Paper Selection

Guides on selecting the appropriate paper source for copying.

Duplex

Explains how to create two-sided copies.

2 Sending Functions

Original Size Selection

Guides on selecting the original size for scanning documents for sending.

3 Printer

Emulation

Explains how to select emulation options for operating the machine with commands from other printers.

4 Using Document Box

5 Status; Job Cancel

Checking Job Status

Pause and Resumption of Jobs

Checking the Remaining Amount of Toner and Paper

6 System Menu

Network Setup

Adjustment;Maintenance

7 Management

User Login Administration

Specifies how user access is administered, including enabling and disabling login.

Job Accounting

Manages copy/print counts per account, tracking usage, and restricting usage.

8 Security

Security Kit Functions

Explains overwriting and encryption for data security.

Installing the Security Kit

Provides instructions for administrators on installing the Security Kit.

System Initialization

Utax CD 1325 Specifications

General

Print Technology	Laser
Print Speed (Mono)	25 ppm
Print Speed (Color)	25 ppm
Copy Speed (Black)	25 cpm
Copy Speed (Color)	25 cpm
Copy Resolution	600 x 600 dpi
Max Paper Size	A4
Processor frequency	800 MHz
Monthly Duty Cycle	50000 pages
Scanner Type	ADF
Scan to	USB
Connectivity	Ethernet
Operating System Compatibility	Windows, Mac, Linux
Weight	Approx. 30 kg
Type	Color