EasyManua.ls Logo

VEVOR LB200T - User Manual

VEVOR LB200T
172 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Technical Support and E-Warranty Certificate www.vevor.com/support
ICE MACHNE
MODEL:LB100T/LB160T/LB200T/LB265T
We continue to be committed to provide you tools with competitive price.
"Save Half", "Half Price" or any other similar expressions used by us only represents an
estimate of savings you might benefit from buying certain tools with us compared to the major
top brands and does not necessarily mean to cover all categories of tools offered by us. You
are kindly reminded to verify carefully when you are placing an order with us if you are
actually saving half in comparison with the top major brands.

Questions and Answers

  • R
    rdunnAug 15, 2025
    Why is the ice block from my VEVOR LB200T thin?
    • T
      taylorricardoAug 15, 2025
      If the ice block produced by your VEVOR Ice Maker is too thin, several factors could be responsible. First, try cleaning the surface of the condenser, as dust accumulation can cause this issue. Ensure that the ambient temperature is within the recommended range for the machine. Also, check for refrigerant leaks and recharge if necessary. Other potential causes include a broken fan motor (replace it), a blocked spray tube (clean it), or an ice thickness sensor positioned too close to the ice model (adjust the sensor screw by turning it to the right).
  • L
    Lauren ThomasAug 18, 2025
    What to do if the ice can not drop off from VEVOR LB200T?
    • C
      Connor SimmonsAug 18, 2025
      If the ice isn't dropping off in your VEVOR Ice Maker, the ice thickness sensor might be broken, and you should replace it. Another potential issue is that the solenoid valve isn't opening. Check the electric wire to ensure it's properly connected, and if not, replace the solenoid valve. Finally, the ambient temperature may be too low; ensure you're using the machine within the allowable ambient temperature range.
  • E
    Erik GibsonAug 21, 2025
    What to do if no water flowing on to the ice model in VEVOR Ice Maker?
    • J
      Jack HessAug 22, 2025
      If there is no water flowing onto the ice model in your VEVOR Ice Maker, the water pump or the PC board may be broken, and you should replace it.
  • M
    Mark RichardsonAug 25, 2025
    What to do if the sink is overflow in VEVOR Ice Maker?
    • S
      Sabrina CookAug 26, 2025
      If the sink is overflowing in your VEVOR Ice Maker, the water supply solenoid valve or the water level sensor might be broken, and you should replace it.
  • K
    Keith OlsonAug 28, 2025
    How to fix loose connecting wire of compressor’s starter in VEVOR Ice Maker?
    • G
      Gavin McfarlandAug 28, 2025
      If the connecting wire of the compressor’s starter is loose on your VEVOR Ice Maker, check and fasten it.
  • C
    Courtney ThompsonAug 31, 2025
    What to do if the starting capacitor of compressor is broken in VEVOR Ice Maker?
    • J
      johnjohnsonAug 31, 2025
      If the starting capacitor of the compressor in your VEVOR Ice Maker is broken, replace it.
  • D
    Diana GoodmanSep 3, 2025
    What to do if water level sensor is broken in VEVOR LB200T?
    • R
      Roger HayesSep 3, 2025
      If the water level sensor is broken in your VEVOR Ice Maker, replace it.
  • C
    Carrie LaraSep 7, 2025
    What to do if water pump is broken in VEVOR Ice Maker?
    • A
      Alison JohnstonSep 7, 2025
      If the water pump is broken in your VEVOR Ice Maker, replace it.
  • C
    Cheyenne TownsendSep 12, 2025
    What to do if PC board is broken in VEVOR LB200T?
    • J
      Jose PattersonSep 12, 2025
      If the PC board is broken in your VEVOR Ice Maker, replace it.

Summary

VEVOR Ice Machine Introduction

Technical Support and E-Warranty

Information on technical assistance and electronic warranty for the product.

Product Support Contact

Important Safety Safeguards

Safety Alert Symbols and Definitions

Explanation of safety alert symbols, warnings, and cautions for hazard identification.

Correct Product Disposal

Guidelines for proper disposal of the product according to environmental regulations.

General Safety Precautions

Usage Restrictions and Operational Warnings

Ice Machine Dimensions

Included Packing List

Basic Structure and Components

User Notices and Information

Installation and Setup Guide

LCD Display and Control Panel

Daily Cleaning and Maintenance Procedures

Ice Thickness Setting Reference

Reference table for ice thickness setting based on ambient temperature.

Troubleshooting Common Issues

Technical Parameters and Wiring Diagrams

VEVOR LB200T Specifications

General IconGeneral
BrandVEVOR
ModelLB200T
CategoryIce Maker
LanguageEnglish

Related product manuals