Videx GSM Lite 4000 Series - Programming Guide; Return System to Preset Engineers Factory Code; Technical Specification

66250756-EN - V2.1 - 05/11/19
- 14 -
4000 Series GSM Lite Audio Intercom - Technical Manual
4000 Series GSM Lite Audio Intercom
Art. 4901 Technical Information
PROGRAMMING GUIDE
• Enter the ENGINEER’S CODE: rst time type six times 1 (111111
factory default) and press ENTER(the red LED will illuminate);
• Conrm ENGINEER’S CODE: re-type the same code again or
type a new code (4 to 8 digits) then press ENTER (melody);
• Enter the code (4 to 8 digits) to enable RELAY 1 then press
ENTER (melody);
• Enter the RELAY 1 operation time (2 digits 01 to 99, i.e. 05 = 5
seconds, 00 = latch) then press ENTER (melody);
• Enter the code (4 to 8 digits) to enable RELAY 2 then press
ENTER (melody);
• Enter the RELAY 2 operation time (2 digits 01 to 99, i.e. 05 = 5
seconds, 00 = latch) then press ENTER (melody);
• Enter the code (4 to 8 digits) to enable RELAY 3 then press
ENTER (melody);
• Enter the RELAY 3 operation time (2 digits 01 to 99, i.e. 05 = 5
seconds, 00 = latch) then press ENTER (melody);
• The system is ready to use (the red LED will switch OFF).
PROGRAMMING NOTES
• Pressing the ENTER button twice during the programming
process, without changing any parameters, will exit from the
programming menu.
• When entering a relay code it must be dierent from the
ENGINEER'S CODE.
• To latch the relay type in the access code then press ENTER
to conrm. To unlatch the relay type in the same access code
again then press CLEAR to conrm.
RETURN SYSTEM TO PRESET ENGINEER’S FACTORY CODE
• Turn OFF the power to the codelock;
• Keep the ENTER button pressed while the power is turned
back ON;
• Release the ENTER button;
• The ENGINEER’s CODE is now reset back to 6x1 (“111111”).
ENTER THE
“ENGINEER’S CODE”
CONFIRM
OR CHANGE
“ENGINEER’S CODE”
ENTER
“ACCESS 1 CODE”
ENTER
“ACCESS 1 TIME”
ENTER
“ACCESS 2 CODE”
ENTER
“ACCESS 2 TIME”
SYSTEM
READY TO USE
ENTER
“ACCESS 3 CODE”
ENTER
“ACCESS 3 TIME”
Press ENTER
(red LED ON)
Press ENTER
(melody)
Press ENTER
(melody)
Press ENTER
(melody)
Press ENTER
(melody)
Press 1 six times
“111111”
(factory default)
Press 1 six times
“111111” again or
type new engineer’s
code (4 to 8 digits)
Type code to enable
relay 1 (4 to 8 digits)
Type code to enable
relay 2 (4 to 8 digits)
Two digits (01 to 99)
i.e. 05 = 5 seconds,
00 = latching
Two digits (01 to 99)
i.e. 05 = 5 seconds,
00 = latching
red LED OFF
Press ENTER
(melody)
Type code to enable
relay 3 (4 to 8 digits)
Two digits (01 to 99)
i.e. 05 = 5 seconds,
00 = latching
Press ENTER
(melody)
Press ENTER
(melody)
TERMINAL CONNECTIONS TECHNICAL SPECIFICATION
Connection Description Working voltage: 12V - 24Vac/dc +/- 10%
+ 12-24V AC or DC power input Current consumption: 20mA (standby); 70mA (max.)
- 0V power input Number of relays: 3, RLY1, RLY2 & RLY3 (C, NC and NO)
C1 Relay 1 common connection
Relay contacts:
3A @ 4Vac⁄dc (max)
Relay current ⁄ voltage: 3A @ 24Vac/dc (max.)
NO1 Relay 1 normally open connection Push to exit inputs: 2, SW1 and SW2 (switched 0V)
NC1 Relay 1 normally closed connection Back EMF protection: Yes, 3x MOV jumpers
C2 Relay 2 common connection Number of codes: 3 codes (1 code per relay)
NO2 Relay 2 normally open connection Programming: Via keypad
NC2 Relay 2 normally closed connection Working Temperature: -10 +50
o
C
C3 Relay 3 common connection
NO3 Relay 3 normally open connection
NC3 Relay 3 normally closed connection
SW1 Switched 0V PTE input to trigger relay 1
SW2 Switched 0V PTE input to trigger relay 2