Videx GSM Lite 4000 Series - Storing the Call Button Telephone Numbers (STN and STD); Storing the Primary and Divert Number in a Single Text Message (Using STN)

66250756-EN - V2.1 - 05/11/19
- 30 -
4000 Series GSM Lite Audio Intercom - Technical Manual
4000 Series GSM Lite Audio Intercom
Programming the GSM Intercom
Send tone after answer (But 1) DTP 1111DTPn n = 0 - 9 or X X 37
Send tone after answer (Div 1) DTD 1111DTDn n = 0 - 9 or X X 37
Send DTMF tone delay DTT 1111DTTnn nn = 01 - 12 03 37
Enable dial 0 on answer function EDZ 1111EDZnn? nn = 00 or 01 00 37 - 38
Enable # (hash) function ED# 1111ED#nn? nn = 00 or 01 00 38
Find a telephone number FDT 1111FDT” number or ends in” n/a n/a 38
End on Last Divert EOD 1111EODnn? nn = 00 or 01 00 38
Shutdown and Restart RBT 1111RBT n/a n/a 39
Simulate button press via SMS BUT 1111BUTnn nn = 01 - 50 n/a 39
Initiate a special command PRG 1111PRG(command) AT commands n/a 39
AT command to send at start up AT1 1111AT1”ATxxxxxx”? Any AT command n/a 39
AT command to send at start up AT2 1111AT2”ATxxxxxx”? Any AT command n/a 39
AT command to send at start up AT3 1111AT3”ATxxxxxx”? Any AT command n/a 39
Obtain the GSM’s IMEI number IME 1111IME? n/a n/a 39
Unlatch prevention feature LLA 1111LLAnn? nn = 00 or 01 00 40
OPTIONAL DATA
The optional data will vary depending on the command used. It may be a telephone number, a time
setting or may not be used at all. For more information refer to the following command settings.
OPTIONAL ?
Most of the commands support the ? feature. When this is added to the end of the text message, a
conrmation text message will be sent back to the sender indicating the new data has been received
and stored.
When sending text messages there may be a delay from when you send the message to when it is received by the GSM LITE
depending on how congested the network is. If you are at the intercom panel when sending the message you will hear a single
beep from the GSM LITE intercom to indicate it has received the message.
STORING THE CALL BUTTON TELEPHONE NUMBERS STN AND STD
Telephone numbers can be stored for the 4 available call buttons. Each call button can call two telephone numbers, if the rst
number is busy or not answered in a certain time it can call a second number if the divert facility is setup. The STN code stores the
rst number called (primary number) when the button is pressed, while the STD code stores the second number to be called (divert
number) if the rst is busy or not answered. The messages to store/check numbers are as follows (replace STN with STD when
storing/checking divert number).
1111STNnnn”yyyyyyyyyyy” Store the primary telephone number yyyyyyyyyyy in position nnn.
1111STNnnn”yyyyyyyyyyy”? Store the telephone number yyyyyyyyyy in position nnn and send a conrmation text
message to conrm storage of new number.
1111STNnnn? Query the telephone number stored in location nnn. A text message will be sent to the
sender with the stored number for that location.
1111STNnnn”” Delete the telephone number stored in location nnn.
1111STNnnn””? Delete the telephone number stored in location nnn. A text message will be sent to the
sender with the delete conrmation for that location.
nnn is a button number between 001 and 004. The telephone number y can be a maximum of 30 digits. For example: to store the
number 01912243174 for button 2 and a divert number (if the rst one is not answered or busy) of 01912241558, the two SMS
messages would be sent to the GSM intercom:
1111STN002”01912243174” (primary no.)
followed by,
1111STD002”01912241558” (divert no.)
IMPORTANT NOTE: When sending the command 1111STNnnn? to query the telephone number stored for the call button the
GSM LITE will reply with the list of all the numbers stored for that call button i.e. the primary number and the divert number as
shown in the example below *.
STORING THE PRIMARY AND DIVERT NUMBER IN A SINGLE TEXT MESSAGE USING STN
It is also possible to program the primary telephone number and the divert number for a particular call button in a single text
message instead of using the individual programming codes STN and STD for the numbers. Expanding on the STN programming
command the text messages used to store/check the primary number and divert number are as follows.
1111STNnnn”pn” (or 1111STNnnn”yyyyyyyyyyy”)
1111STNnnn”pn”,”dn”
Store the primary number and divert number in position nnn, (where pn =
primary no, dn = divert no and nnn = call button 001 - 004).