Videx VR4KGSM-1 - Storing Call Button Numbers

66250675-EN - V1.0 - 05/09/17
39
4000 Series Vandal Resistant GSM - Technical Manual
4000 Series Vandal Resistant GSM Audio Intercom with Proximity Facility
Programming the GSM Intercom
Send DTMF tone delay DTT 1111DTTnn nn = 01 - 12 03 44 - 45
Enable dial 0 on answer function EDZ 1111EDZnn? nn = 00 or 01 00 45
Enable # (hash) function ED# 1111ED#nn? nn = 00 or 01 00 45
Enable proximity EPR 1111EPRnn? nn = 00 or 01 00 46
Proximity number of bytes to
check
PBY 1111PBYnn? nn = 02, 03 or 04 02 46
Store/query a fob or card FOB 1111FOBnnn”site”,”user” nnn = 000 - 999 n/a 46 - 47
Find a telephone number FDT 1111FDT” number or ends in” n/a n/a 47
Find a fob or card number FDF 1111FDF”user code” n/a n/a 47
Shutdown and Restart RBT 1111RBT n/a n/a 48
Initiate a special command PRG 1111PRG(command) AT commands n/a 48
AT command to send at start up AT1 1111AT1”ATxxxxxx”? Any AT command n/a 48
AT command to send at start up AT2 1111AT2”ATxxxxxx”? Any AT command n/a 48
AT command to send at start up AT3 1111AT3”ATxxxxxx”? Any AT command n/a 48
OPTIONAL DATA The optional data will vary depending on the command used. It may be a telephone number,
a time setting or may not be used at all. For more information refer to the following command
settings.
OPTIONAL ? Most of the commands support the ? feature. When this is added to the end of the text message,
a conrmation text message will be sent back to the sender indicating the new data has been
received and stored.
When sending text messages there may be a delay from when you send the message to when it is received by the GSM intercom
depending on how congested the network is. If you are at the door panel when sending the message you will hear a short single
beep from the GSM intercom to indicate it has successfully received the message. For unsuccessful (error) messages the GSM
intercom will indicate this with two long beeps.
STORING THE CALL BUTTON TELEPHONE NUMBERS STN, STD, STE AND STF
Telephone numbers can be stored for the 24 available call buttons. Each call button can call up to four telephone numbers (if the
rst is busy or not answered in a certain time it can call a 2nd, 3rd and 4th number if the divert facility is setup). The STN code stores
the rst number called (primary telephone number) when the button is pressed. The STD, STE and STF codes stores the diverted
telephone numbers if the rst is busy or not answered (the GSM intercom will divert to the 2nd number then divert to the 3rd
number and nally the 4th number). The messages to store/check numbers are as follows (replace STN with STD, STE or STF when
storing/checking divert numbers).
1111STNnnn”yyyyyyyyyyy” Store the primary telephone number yyyyyyyyyyy in position nnn.
1111STNnnn”yyyyyyyyyyy”? Store the telephone number yyyyyyyyyy in position nnn and send a conrmation text
message to conrm storage of new number.
1111STNnnn? Query the telephone number stored in location nnn. A text message will be sent to the
sender with the stored number for that location.
1111STNnnn”” Delete the telephone number stored in location nnn.
1111STNnnn””? Delete the telephone number stored in location nnn. A text message will be sent to the
sender with the delete conrmation for that location.
nnn is a button number between 001 & 024. The telephone number y can be a maximum of 30 digits. For example: to store the
number 01912243174 for button 5 and three divert numbers (if that one is not answered or busy) of 01912241558, 07771234567
and 01912241559 respectively, the following SMS messages would be sent to the GSM intercom:
1111STN005”01912243174”
1111STD005”01912241558”
1111STE005”07771234567”
1111STF005”01912241559”