Videx VR4KGSM-1 - Programming the GSM Intercom; Programming by Text Message

66250675-EN - V1.0 - 05/09/17
38
4000 Series Vandal Resistant GSM - Technical Manual
4000 Series Vandal Resistant GSM Audio Intercom with Proximity Facility
Programming the GSM Intercom
PROGRAMMING THE GSM INTERCOM
Programming the GSM intercom can be carried out in two ways, either by sending text (SMS) messages or by using the GSMSK PC
software (ver 3.1.0.10 or later), also refer to the programming manual GSMSK-66251720-EN-V1-3 (or later).
IMPORTANT NOTE: When you are required to use “ in a text message it is very important to use the correct symbol and not for
example ‘ (or two ‘ single apostrophes side by side which you will see look the same but will be interpreted dierently by the
GSM intercom panel).
PROGRAMMING BY TEXT MESSAGE
Programming by text message is a simple way to customise the settings of the GSM intercom panel and add or delete telephone
numbers. If you have a large number of buttons or telephone numbers to enter you may nd programming easier with the GSMSK
PC software. Simply send texts in the following format shown below to the telephone number of the SIM within the GSM intercom
panel:
<4 DIGIT CODE> <3 DIGIT FUNCTION CODE> <OPTIONAL DATA> <OPTIONAL ?>
4 DIGIT CODE This code prevents unauthorised access to the programmable features of the system. The code
must be four digits long but can be any combination using digits 0 – 9. The default code is 1111
and will be used for all examples in this manual.
3 DIGIT FUNCTION CODE The 3 digit function code identies the programmable feature to be changed. The code must
be in capital letters. The following table lists the available codes.
DESCRIPTION CODE EXAMPLE SETTINGS DEFAULT PAGE
Store a primary telephone no. STN 1111STNnnn”01912243174” nnn = 001 - 024 n/a 39
Store divert 1 telephone no. STD 1111STDnnn”01912241559” nnn = 001 - 024 n/a 39
Store divert 2 telephone no. STE 1111STEnnn”01912243678” nnn = 001 - 024 n/a 39
Store divert 3 telephone no. STF 1111STFnnn”01912245326” nnn = 001 - 024 n/a 39
Store dial to open no. STR 1111STRnnn”07771234567” nnn = 000 - 999 n/a 40
Set call time SPT 1111SPTnn nn = 01 - 12 02 (40s) 40
Set relay time RLT 1111RLTnn nn = 00 - 99 05 (5s) 40
Set auxiliary AO output time A1T 1111A1Tnn nn = 00 - 99 05 (5s) 40
Set auxiliary AO out mode A1M 1111A1Mnn nn = 00 - 02 01 41
Keep connection facility NOD 1111NODnn nn = 01 - 99 0 (disabled) 41
Divert to next no. time DIT 1111DITnn nn = 01 - 99 15 (15s) 41
Check GSM signal strength SIG 1111SIG? n/a n/a 41
Check software version VER 1111VER? n/a n/a 41
Dial a number DLE 1111DLE”123” n/a n/a 42
Change 4 digit code CDE 1111CDE1234 Any 4 digits 1111 42
Trigger the relay RLY 1111RLY n/a n/a 42
Trigger the auxiliary output AO A1O 1111A1O n/a n/a 42
Store balance check dial string SDL 1111SDL”*#1345#” n/a n/a 42
Check credit balance BAL 1111BAL? n/a n/a 42 - 43
Store master telephone no. STM 1111STM”07771234567” n/a n/a 43
Latch the relay RLA 1111RLA n/a n/a 43
Unlatch the relay RUL 1111RUL n/a n/a 43
Latch the auxiliary AO output A1L 1111A1L n/a n/a 43
Unlatch the auxiliary AO output A1U 1111A1U n/a n/a 43
Store time band TBA 1111TBA”06002300” HHMMHHMM 00002359 44
Check/Set date & time CLK 1111CLK”yy/mm/dd,hh:mm”? yy/mm/dd,hh:mm n/a 44
Silent dialling mode AUE 1111AUEnn nn = 00 or 01 01 44
Send tone after answer (But 1) DTP 1111DTPn n = 0 - 9 or X X 44 - 45
Send tone after answer (Div 1) DTD 1111DTDn n = 0 - 9 or X X 44 - 45