Viper AS710R - User Manual

Questions and Answers

M
michaelwellsAug 16, 2025
What to do if the Viper Scrubber isn't vacuuming dirty water well?
- C
  christina32Aug 16, 2025
  If the dirty water vacuuming is insufficient in your Viper Scrubber, several factors could be the cause. The recovery tank might be full, indicated by a red light(E2), in which case you should empty the recovery tank. Also, the hose could be disconnected from the squeegee; if so, reconnect it. Check for clogs in the vacuum assembly and clean if necessary. The squeegee might be dirty, or the blades worn or damaged, requiring cleaning and inspection. Finally, ensure the tank cover(A2) is properly closed and the gasket is intact; close it properly or replace the gasket if damaged.
M
Michelle FreemanAug 19, 2025
How to fix insufficient solution flow in my Viper Scrubber?
- F
  Felicia BarrSep 12, 2025
  If the solution flow is insufficient in your Viper Scrubber, start by checking the solution filter (D3) for dirt and clean it if necessary. Ensure the solution tank is full, as indicated by the light(E10) being red when empty; fill it with water. Verify that the water switch (D2) is not set to “0” and open the water switch. Lastly, inspect the solution tank for dirt and clean it if needed.
J
John WoodsAug 22, 2025
Why won't my Viper Scrubber move forward or backward?
- C
  Chloe FlowersAug 22, 2025
  If your Viper Scrubber isn't moving forward or backward, there are several potential causes. First, the PCB or key board might be broken, requiring replacement. Check if the Emergency-stop button(A15) is engaged and release it by turning. Ensure the seat limit switch is activated by sitting on the seat. Also, if the squeegee is not lifted in reverse and the LED screen (E1) displays ERR-01, lift the squeegee.
S
Steven StoneAug 25, 2025
What to do if the vacuum motor of my Viper Scrubber isn't working?
- R
  Robert GordonAug 26, 2025
  If the vacuum system motor in your Viper Scrubber isn't working, the recovery tank might be full, indicated by a red light(E2); empty the recovery tank. Alternatively, the vacuum motor could be overloaded; check the motor and reset the breaker. A broken PCB or key board could also be the cause, requiring replacement.
R
Robert LewisAug 28, 2025
Why isn't the brush motor working on my Viper Scrubber?
- L
  Lisa WardAug 28, 2025
  If the brush motor in your Viper Scrubber isn't working and the indicator light isn't on, the PCB or key board might be broken, requiring replacement. The deck motor could be overloaded; try using less aggressive brushes suitable for the floor and reset the breaker. Also, check for foreign materials preventing the brush from rotating and clean the brush hub if necessary.
D
Daniel MartinezAug 31, 2025
How to fix a Viper Scrubber that won't turn on (LED screen E1 off)?
- N
  Nicholas WangAug 31, 2025
  If your Viper Scrubber isn't turning on and the LED screen (E1) remains off, it could be due to a disconnected battery connector; ensure it is properly connected. Alternatively, the batteries might be completely discharged; charge them fully.
W
William BryantSep 3, 2025
Why does the squeegee on my Viper Scrubber leave marks?
- B
  Becky GomezSep 3, 2025
  If the squeegee on your Viper Scrubber is leaving marks on the floor, there might be debris under the squeegee blades; remove any debris. The squeegee blades may also be worn, chipped, or torn, requiring replacement.
L
Leslie SalazarSep 6, 2025
What does a red indicator light (E11) mean on my Viper Scrubber?
- K
  Keith MiddletonSep 6, 2025
  If your Viper Scrubber isn't working and the indicator light (E11) is red, the batteries are likely discharged. You should charge the batteries.
C
Cassandra CraigSep 9, 2025
What to do if the drive motor on my Viper Scrubber doesn't work?
- B
  bsmithSep 9, 2025
  If the drive motor of your Viper Scrubber isn't working, and the error indicator (E4) is lit, refer to ERROR INFORMATION. If the drive motor is overloaded, check the drive motor and reset the breaker.
J
Justin TaylorSep 12, 2025
Why can't my Viper Scrubber brake?
- C
  collinskathrynSep 12, 2025
  If your Viper Scrubber cannot brake, it may be because the drive motor brake is not applied. This can happen if the brake bracket is stuck.