Viscount Cantorum Trio Plus - Save the Organ Configuration in a USB Flash Drive (Save Snapshot Function); Load an Organ Configuration from a USB Flash Drive (Load Snapshot Function); Restore the Factory Organ Configuration (Factory Reset Function)

EN - 34
Cantorum Trio – Duo Plus Reference Manual
Backup, restore and factory reset of organ configuration
(Backup/Restore menu)
Save the organ configuration in a USB flash drive (SAVE SNAPSHOT function)
To save the entire organ configuration (Pipe Sets, combinations, settings) in a USB flash drive as a .ALL file, follow this
procedure:
1. insert a USB flash drive in the USB [TO DEVICE] connector on the rear panel,
2. in the main video page press the [MENU/ENTER] button,
3. select the BACKUP/RESTORE field,
4. select the SAVE SNAPSHOT field,
5. assign a name to the file that will be saved in the USB flash drive. The system
proposes a name as “SNAP” and the date actually setted in the organ (see
page 36), to modify it use the [ ] and [ ] buttons to move the cursor, [+] and
[-] to select the character.
6. press [MENU/ENTER] to save (or [EXIT] to quit) and wait the “FILE SAVED”
message. A .ALL file will be saved in the “v_settings” folder of the USB flash drive.
Load an organ configuration from a USB flash drive (LOAD SNAPSHOT function)
To load an entire organ configuration or single sections (Pipe Sets, combinations, settings) from a USB flash drive
saved as a .ALL file using the SAVE SNAPSHOT function (see above), follow this procedure:
1. insert the USB flash drive with the .ALL file(s) in the USB [TO DEVICE] connector on the rear panel,
2. in the main video page press the [MENU/ENTER] button,
3. select the BACKUP/RESTORE field,
4. select the LOAD SNAPSHOT field,
5. select the .ALL file of the organ configuration you want to load and press the
[MENU/ENTER] button,
6. select what you want to load of the .ALL file into the organ:
- Entire Snapshot: the entire organ configuration
- Only Combinations: all the combinations
- Only Pipe Sets: all the Pipe Sets
- Only Settings: all the organ settings
Refer to the table above in “What a Snapshot contains” to know in detail what
a Snapshot section contains.
7. press [MENU/ENTER] button to confirm the load and wait the reboot of the organ (if ENTIRE SNAPSHOT,
ONLY COMBINATIONS or ONLY PIPESETS option was selected) or the “SNAPSHOT RESTORED”
message, or [EXIT] to quit.
Restore the factory organ configuration (FACTORY RESET function)
To restore the entire organ configuration (Pipe Sets, combinations, settings) to the
factory conditions, follow this procedure:
1. in the main video page press the [MENU/ENTER] button,
2. select the BACKUP/RESTORE field,
3. select the FACTORY RESET field,
4. at the message “RESTORING TO FACTORY STATUS, PROCEED?” press
[MENU/ENTER] to confirm or [EXIT] to abort.
NOTES
-
Please pay very close attention when loading a Snapshot, because the actual configuration of your organ
will be irreparably lost. To avoid this, before load a .ALL file, save the actual organ configuration in USB
flash drive using the SAVE SNAPSHOT function and, if necessary, reload it using the LOAD SNAPSHOT
function (see above).
-
Loading a .ALL file (using the Entire Snapshot or Only Pipesets options) containing a different stop list,
the display will show the message “DIFFERENT STOP LIST FOUND. REPLEACE PIPESETS
ANYWAY?”, remembering you that one or more stop label will not match with the played voice (and so
possibly you will have to move the labels). Press [MENU/ENTER] to confirm the load or [EXIT] to quit.
-
It is not possible to load a .ALL file created with a different organ model. In this case the display will show
the message “DIFFERENT ORGAN MODEL LOAD ABORTED”.
-
If you wish to rename .ALL files saved to the USB stick using a computer, always make sure that the
names can be a maximum of 12 characters and cannot contain special characters such as “$”, “@”, “#”,
etc. The “_” will be automatically converted as a space.