24 DE5467U
Motion Detector, Wireless: A passive Infrared motion
sensor and a wireless PowerCode transmitter in a shared
housing. Upon sensing motion, the detector transmits its
unique identification code, accompanied by an alarm signal
and various other status signals to the control panel. After
transmission, it stands by to sense further motion.
Non-Alarm Zone: Your installer can designate a zone for
roles other than alarm. For instance, a motion detector
installed in a dark stairway may be used to switch on lights
automatically when someone crosses the dark area. Another
example is a miniature wireless transmitter linked to a zone
that controls a gate opening mechanism.
Quick Arming: Arming without a user code. The control panel
does not request your user code when you press one of the
arming buttons. Permission to use this arming method is given
or denied by the installer while programming the system.
Remote Responder: A responder can be either a
professional service provider to which the home or business
owner subscribes (a central monitoring station) or a family
relation/friend who agrees to look after the protected site
during absence of its occupants. The control panel reports
events by telephone to both kinds of responders.
Restore: When a detector reverts from the state of alarm to
the normal standby state, it is said to have been “restored”.
A motion detector restores automatically after detection of
movement, and becomes ready to detect again. This kind of
“restore” is not reported
to the remote responders.
A magnetic contact detector restores only upon closure of the
protected door or window. This kind of “restore” is reported
to
the remote responders.
Smoke Detector, Wireless: A regular smoke detector and a
wireless PowerCode transmitter in a shared housing. Upon
detection of smoke, the detector transmits its unique
identification code accompanied by an alarm signal and various
status signals to the control panel. Since the smoke detector is
linked to a special fire zone, a fire alarm is initiated.
User Codes: The PowerMax+ is designed to obey your
commands, provided that they are preceded by a valid
security access code. Unauthorized people do not know this
code, so any attempt on their part to disarm or defeat the
system is bound to fail. Some operations, however, can be
carried out without a user code as they do not degrade the
security level of the alarm system.
Zone: A zone is an area within the protected site under
supervision of a specific detector. During programming, the
installer allows the control panel to learn the detector’s
identity code and links it to the desired zone. Since the zone
is distinguished by number and name, the control panel can
report the zone status to the user and register in its memory
all the events reported by the zone detector. Instant and
delay zones are “on watch” only when the control panel is
armed, and other (24-hour) zones are “on watch” regardless
of whether the system is armed or not.
FCC STATEMENT
The 315 MHz model of this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference that may be received, including interference
that may cause undesired operation.
The digital circuit of this device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio and television reception. However, there is no guarantee that interference will not occur in a
particular installation. If this device does cause such interference, which can be verified by turning the device off and on, the user is
encouraged to eliminate the interference by one or more of the following measures:
– Re-orient or re-locate the receiving antenna.
– Increase the distance between the device and the receiver.
– Connect the device to an outlet on a circuit different from the one which supplies power to the receiver.
– Consult the dealer or an experienced radio/TV technician.
At 315 MHz the product complies with FCC requirements.
FCC Declaration of Conformity
(See notes)
We, the undersigned,
Visonic Inc.
10 Northwood Drive, Bloomfield, CT 06002, U.S.A.
Phone number: 860-243-0833, Fax number: 860-242-8094
are the Responsible Party for this Declaration, certify and declare under our sole responsibility that the following equipment:
Brand Type Product description
Visonic Powermax+ Wireless security system
complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Drawn up in: BLOOMFIELD CT. 06002-1911. PHONE: (860) 243-
0833, (800) 223-0020. FAX: (860) 242-8094
on 1/19/04
Scott Jensen, Technical manager
Note 1: This statement shall be supplied with the product at the time of marketing or importation.
Note 2: This statement shall be included in the user’s manual or as a separate sheet.
Note 3: The responsible party for a Declaration of Conformity must be located within the United States.
Note 4: The responsible party for a Declaration of Conformity can be either: manufacturer (if located within the United States), or the importer.
VISONIC LTD. (ISRAEL):
P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: (972-3) 645-6789, FAX: (972-3) 645-6788
VISONIC INC. (U.S.A.): 10 NORTHWOOD DRIVE, BLOOMFIELD CT. 06002-1911. PHONE: (860) 243-0833, (800) 223-0020. FAX: (860) 242-8094
VISONIC LTD. (UK): FRASER ROAD, PRIORY BUSINESS PARK, BEDFORD MK44 3WH. PHONE: (0870) 7300800 FAX: (0870) 7300801
INTERNET: www.visonic.com
VISONIC LTD. 2004 POWERMAX+ USER GUIDE DE5467U (REV. 0, 02/04)
To Previous Page
Loading...
