Vitus Audio Reference Series - The Elements in the Menu

18 | RD-101 Owner’s manual
3. OPERATION3. OPERATION
The elements in the menu The elements in the menu
You can modify the settings of your RD-101 by entering the menu and selecting
the options you require. Refer to the menu structure diagram on page 21 for specific
information.
The sub-menus are highlighted in different colours.
SETUP, OUTPUT, REMOTE, AutoStb, RESET, V.INIT, BP VOL, LOGO, BRIGHT, INPUTS
See chapter 7 for options on modifying settings.
SETUP
Change the settings of the RD-101.
OUTPUT
Here you can switch between RCA OUT and XLR OUT.
REMOTE SETTINGS
The RD-101 is standard shipped with a Apple Remote.
The Apple remote that comes with the RD-101 can be used
on all Reference devices. If you own two (or more) reference
devices than it is recommended that you pair the remote(s)
with their devices.
REMOTE ID
Show the ID of the remote.
UNPAIR
Un-pair the remote and the RD-101 by removing the REMOTE ID.
DATA
Shows information about this RD-101.
AutoStb
Choose if the product should automatically enter standby mode
afterthe buttons on the remote or on the front of the unit haven’t
been used for X minutes.
RESET
Restore the settings of the RD-101 to its default settings.
V.INIT
Change settings for the initial volume step of the RD-101.
The RD-101 has a default volume step of -50 dB. You can set the
volume step to a step, between -99.0 dB to +12 dB.This step will
be the new volume step. Even when after the power cord has
been disconnected the RD-101 still starts up in the new volume step.
BP VOL
Switch between BP OFF (enable volume control) or BP ON (disable
volume control).
LOGO
Turn ON/OFF the VA logo on the front panel
BRIGHT
Change the brightness of the display to 0, 1, 2 or 3.
INPUTS
Change settings for each input.
INPUT (1-5)
The RD-101 has 5 analog inputs.
The settings for each individual input can be adjusted in the menu.
The input selection is saved automatically every 10 minutes.
Each time you initialise the RD-101 the last saved setting is restored.
You can manually save a setting by pressing the MENU button
down 2-3 sec. When “SAVE” is shown in the display, the setting
has been saved.
STREAMER
Here you can set the RD-101 to automatically check for rmware
updates for the streamer. In the streamer settings the update check
can be enabled/disabled. (note: all rmware updates made available
are tested and approved by Vitus Audio).
INPUT NAME SETTINGS
By default, the inputs are named DIG 2/3/4/5, USB and Streamer.
In the text-menu you can nd a list of predened input names.
If the name of your device is not in the list, you can choose to make
your own device name.
ADJUST
Adjust the xed dB step to any step between -89 dB and +13dB.
This function is only available when FIX ON is selected.
SET FIX
Lock and unlock the volume on a specied input by switching
between FIX ON/FIX OFF.
This feature can be used to congure a home theater bypass input,
if the amplier is used with a surround processor. Input X is now
locked to the SET FIX dB step and can’t be adjusted with the
volume control.
OFFSET
Oset volume setting.
Dierent sources often have dierent output voltages. This has
a direct inuence on the typical volume level that is needed for a
specic sound level, hence changing between sources can result in
a high sound level dierence. To accommodate easy operation, we
have included an oset volume in our ampliers – it simply osets
the volume starting point at a specic volume to match the source.
The oset-value can be set from -12 dB to +12 dB.
SENS
Devices can have dierences in output level. You can adjust the
sensitivity of each input between ≤ 2 Vrms, ≤ 4 Vrms, ≤ 8 Vrms to
minimize these dierences and to prevent clipping of the input.
The sensitivity level needs to be higher than the input level.
TEXT
Lets you change the name of a specied input.
By default the inputs are named input 1, input 2, etc. A list of
predened input names can be found in the text-menu. If the name
of your device is not on the list, you can choose to make your own
device name.
USED
Activates or disactivates specied inputs.
If you only use some of the inputs, it is possible to disable the
inputs that are not used. Using the “Input” button, the system skips
the disabled inputs, and jumps to the next used input.
RD-101 Owner’s manual | 19