Warmup tempo User Manual

(1) Rotary Control (Turn clockwise to increase and anti clockwise to decrease.)
(2) Main Button
(3) Program Slide control (only used during programming)
(4) Mode Slide control
(5) Reset Button
(6) Replaceable CR2032 battery
Operating Guide:
for the Warmup tempo Digital Programmable Thermostat
Part of the Element Series
1.
Normally shows the current temperature in the room. This can be either the oor temperature or the air temperature. (See icon
4). When you are setting a program or manual temperature this icon will temporarily show the set temperature.
2.
During programmed operation this thermometer will show whether the thermostat is at “Comfort” or “Setback” temperature.
The icon will be displayed when “Comfort -1/ -2 is the target temperature. (Only used with the Fil Pilote)
3.
This icon is displayed when the heating is on.
4.
These icons show the type of temperature regulation being used.
Floor Sensor Air Sensor
Regulator (This mode should only be used in special situations, please contact Warmup for additional information).
1
2
3
4
tempo
element
series
TM
exclusivelyfrom
The tempo has been designed with simplicity in mind and is highly intuitive in its programming. The sliders and simple rotary control
make the setting of the thermostat quick and easy.
8
Introduction
ELT-01-XX-01 - Operating guide V1.0 © Warmup plc - 2013

Warmup tempo Specifications

General

Model	Tempo
Category	Thermostat
Compatibility	Electric Underfloor Heating
Maximum Load	16A
Accuracy	±0.5°C
Display	LCD
Programmable	Yes
Floor Sensor	Yes
Air Sensor	Yes

Summary

Introduction

Component Identification

Identifies key physical components of the thermostat, including rotary controls and buttons.

Understanding Display Icons

Explains the meaning of various icons displayed on the thermostat screen for status and information.

Getting Started

Initial Setup and Programming Flow

Guides users through the basic steps to begin programming and setting up the thermostat.

Thermostat Programming

Setting Time and Day of Week

Instructions for configuring the current time and day of the week on the thermostat.

Defining Temperature Schedule Periods

How to set start times for morning, day, evening, and night temperature periods.

Adjusting Comfort and Setback Temperatures

Guides on adjusting specific temperatures for comfort and setback periods.

Selecting Operational Modes

Mode Selection Overview

Explains the different operational modes: Standby, Frost Protection, Manual, and Auto.

Installer Settings Configuration

Clock Format and Measurement Units

Configuration options for clock format (12/24hr) and temperature units (°C/°F).

Temperature Sensor Setup

Settings for selecting and configuring the temperature sensor (Floor, Air, Regulator).

Adaptive Learning Feature

Controls whether the thermostat uses adaptive learning for pre-heating rooms.

Error Messages and Troubleshooting Guide

Interpreting Error Indicators

Explains error icons like floor sensor error, overheat, and low battery.

Resolving Heating and Power Issues

Addresses problems like heating starting too early, incorrect calibration, and no mains power.

Understanding Special Mode Indicators

Explains indicators for Regulator mode, Fil Pilote, and extreme temperature readings (HI/LO).

Warranty and Support

Product Warranty Terms

Outlines the terms and duration of the product's warranty coverage.

Contacting Customer Care

Provides Warmup's contact details for installation or operation questions.

Installation Guide Overview

System Compatibility and Sensors

Introduces the thermostat's role with underfloor heating and the types of sensors it uses.

Electrical Specifications and Safety

Lists the electrical requirements and safety standards for the thermostat.

Placement Recommendations

Advises on optimal locations for the thermostat and floor sensor installation.

Installation and Operation

Wiring and Electrical Connections

Details the specific wiring connections for power supply, heaters, and sensors.

Mounting and Initial Power-Up

Instructions for physically mounting the thermostat and initial power-up sequence.

Product Disposal Information

Advises on the proper disposal of the appliance according to environmental regulations.