EasyManua.ls Logo

Watlow ez-zone pm - Communications Setup and Wiring

Watlow ez-zone pm
133 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Watlow EZ-ZONE
®
PM Integrated Controller 46 Chapter 5 Operations Page
Operations Page
Display
Parameter name
Description
Range Default
Parameter
Appears in
Menu When
Modbus Rela-
tive Address
CIP
Class
Instance
Attribute
hex (dec)
Profibus
Index
Data
Type
&
Read/
Write
[`C;hy]
[ C.hy]
Loop (1 to 2)
Cool Hysteresis
Set the control
switching hysteresis
for on-off control.
This determines
how far into the “on”
region the process
value needs to move
before the output
turns on.
0.001to9,999.000°F
or units
-1,110.555 to
5,555.000°C
3.0°For
units
2.0°C
Cool Al-
gorithm
(Setup
Page) is set
to On-Off.
Instance 1
Map 1 Map 2
1902 2382
Instance 2
Map 1 Map 2
1972 2522
0x97 (151)
1 to 2
0xC (12)
68 float
RWES
[``ti]
[ ti]
Loop (1 to 2)
Time Integral
Set the PID integral
for the outputs.
0 to 9,999 seconds per
repeat
180.0
seconds
per re-
peat
Heat Al-
gorithm or
Cool Algo-
rithm (Set-
up Page) is
set to PID.
Instance 1
Map 1 Map 2
1894 2374
Instance 2
Map 1 Map 2
1964 2444
0x97 (151)
1 to 2
8
69 float
RWES
[``td]
[ td]
Loop (1 to 2)
Time Derivative
Set the PID deriva-
tive time for the out-
puts.
0 to 9,999 seconds 0.0
seconds
Heat Al-
gorithm or
Cool Algo-
rithm (Set-
up Page) is
set to PID.
Instance 1
Map 1 Map 2
1896 2376
Instance 2
Map 1 Map 2
1966 2446
0x97 (151)
1 to 2
9
70 float
RWES
[``dB]
[ db]
Loop (1 to 2)
Dead Band
Set the offset to the
proportional band.
With a negative
value, both heating
and cooling outputs
are active when
the process value is
near the set point. A
positive value keeps
heating and cooling
outputs from fighting
each other.
-1,000.0to1,000.0°F
or units
-556to556°C
0.0 Always Instance 1
Map 1 Map 2
1898 2378
Instance 2
Map 1 Map 2
1968 2448
0x97 (151)
1 to 2
0xA (10)
71 float
RWES
[`o;SP]
[ o.SP]
Loop (1 to 2)
Open Loop Set
Point
Set a fixed level of
output power when
in manual (open-loop)
mode.
-100 to 100% (heat
and cool)
0 to 100% (heat only)
-100 to 0% (cool only)
0.0 Always Instance 1
Map 1 Map 2
2162 2642
Instance 2
Map 1 Map 2
2242 2722
0x6B (107)
1 to 2
2
51 float
RWES
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read with
other interfaces.
* Available with PM4, PM8 and PM9 models only
R: Read
W: Write
E: EE-
PROM
S: User
Set

Table of Contents

Other manuals for Watlow ez-zone pm

Related product manuals