上海维宏电子科技股份有限公司
Weihong Electronic Technology Co., Ltd.
Specialized, Concentrated, Focused - 3 -
3.18.1 Auto Tool Change of Linear Tool Magazine ................................................................................. - 90 -
3.18.2 Auto Tool Change of Circular Tool Magazine ............................................................................... - 91 -
3.18.3 Related Parameters ..................................................................................................................... - 92 -
4 NK280 FOR DUAL Z-AXES MACHINE ...................................................................................................... - 93 -
4.1 MULTIPLE Z AXES CONTROL ........................................................................................................................ - 94 -
4.1.1 Mode Selection ................................................................................................................................ - 94 -
4.1.2 Tool Measurement ........................................................................................................................... - 95 -
4.2 SPECIAL PARAMETERS ................................................................................................................................ - 95 -
5 MAINTENANCE ......................................................................................................................................- 97 -
5.1 OPERATING SYSTEM MAINTENANCE ............................................................................................................. - 98 -
5.1.1 Updating Mirror Image .................................................................................................................... - 99 -
5.1.2 System update ................................................................................................................................. - 99 -
5.1.3 BOOT Update Interface .................................................................................................................. - 101 -
5.2 WARNING INFORMATION ......................................................................................................................... - 103 -
5.3 COMMON TROUBLESHOOTING .................................................................................................................. - 105 -
5.3.1 What should users do if the spindle does not rotate? ................................................................... - 105 -
5.3.2 What should users do if an axis does not move? ........................................................................... - 105 -
5.3.3 What should users do if servo motor Z brake can’t be opened? .................................................... - 105 -
5.3.4 What should users do if machine tool returns to the machine origin abnormally? ....................... - 105 -
5.3.5 What should users do if the machine tool motions upward after arriving at the position of tool
presetter during calibration? .............................................................................................................................. - 106 -
6 DRIVER ................................................................................................................................................ - 107 -
6.1 DRIVER PARAMETERS ............................................................................................................................... - 108 -
6.1.1 Parameter Setting of WISE Servo Driver ........................................................................................ - 108 -
6.1.2 Parameter Setting of YASKAWA Σ–
Ⅱ
Servo Driver ....................................................................... - 109 -
6.1.3 Parameter Setting of YASKAWA Σ-
Ⅴ
/Σ-7 Servo Driver .................................................................. - 111 -
6.1.4 Parameter Setting of PANASONIC MINAS A4 Servo Driver ............................................................ - 112 -
6.1.5 Parameter Setting of PANASONIC MINAS A5 Servo Driver ............................................................ - 113 -
6.1.6 Parameter Setting of MITSUBISHI MR-JE Servo Driver .................................................................. - 115 -
6.1.7 Parameter Setting of MITSUBISHI MR-E Servo Driver .................................................................... - 116 -
6.1.8 Parameter Setting of DELTA ASDA-A Servo Driver .......................................................................... - 117 -
6.1.9 Parameter Setting of DELTA ASDA-B Servo Driver .......................................................................... - 119 -
6.1.10 Parameter Setting of DELTA ASDA-A2 Servo Driver.................................................................... - 120 -
6.1.11 Parameter Setting of DELTA ASDA-B2 Servo Driver .................................................................... - 122 -
6.1.12 Parameter Setting of SANYO PY Servo Driver ............................................................................ - 124 -
6.1.13 Parameter Setting of SANYO R Servo Driver .............................................................................. - 126 -
6.1.14 Parameter Setting of SANYO Q Servo Driver .............................................................................. - 127 -
6.1.15 Parameter Setting of KT270 Servo Driver .................................................................................. - 128 -
6.1.16 Parameter Setting of FUJI FALDIC-β Servo Driver ...................................................................... - 130 -
6.1.17 Parameter Setting of STONE GS Servo Driver ............................................................................ - 131 -
6.1.18 Parameter Setting of TECO TSDA Servo Driver .......................................................................... - 132 -
6.2 WIRING DIAGRAM OF NK280 HOST AND DIFFERENTIAL INPUT STEPPING DRIVER ............................................... - 133 -
6.3 WIRING DIAGRAM OF DRIVER AND TERMINAL BOARD ................................................................................... - 134 -
To Next Page
Loading...
