WEIHONG NK300CX User Manual

上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD
1 / 53
NK300CX CNC Integrated System
Getting Started
Version: 2019.04 17 Version
Author: Document Department
Weihong Corporation, All Rights Reserved
1 System Overview ............................................................................................................................ 3
1.1 NK300CX Host ..................................................................................................................... 3
1.2 WH106C Operation Panel and WH201C Keypad Panel ...................................... 6
1.3 WH108C Operation Panel ............................................................................................ 10
1.4 WH208A1 Operation Panel ......................................................................................... 13
1.5 NK300CX Connection Diagram .................................................................................. 18
1.6 Main Software Interface ............................................................................................... 21
2 Basic Commissioning ................................................................................................................. 22
2.1 Switch the System Configuration .............................................................................. 22
2.2 Adjust I/O Port Polarity ................................................................................................ 23
2.3 Set Commissioning Parameters ................................................................................. 25
2.4 Adjust the Axis Direction ............................................................................................. 28
2.5 Return to the Machine Origin ..................................................................................... 29
2.6 Set the Workbench Travel ........................................................................................... 31
3 Quick Start ...................................................................................................................................... 32
3.1 Load a Program File ....................................................................................................... 32
3.2 Execute Tool Calibration .............................................................................................. 37
3.3 Adjust the WCS ................................................................................................................. 41
3.4 Define the Workpiece Origin ...................................................................................... 43
3.5 Select Tools for Machining .......................................................................................... 45

WEIHONG NK300CX Specifications

General

Brand	WEIHONG
Model	NK300CX
Category	Control Systems
Language	English

Summary

System Overview

NK300CX Host

Introduces the NK300CX host hardware, covering its layout and mounting dimensions.

WH106C Operation Panel and WH201C Keypad Panel

Details the layout and mounting dimensions for WH106C operation and WH201C keypad panels.

WH108C Operation Panel

Covers the layout and mounting dimensions of the WH108C operation panel.

WH208A1 Operation Panel

Describes the layout and mounting dimensions for the WH208A1 operation panel.

NK300CX Connection Diagram

Illustrates NK300CX connection diagrams, detailing hardware connectivity based on system type.

Main Software Interface

Provides an overview of the NK300CX integral software's interactive user interface in AUTO mode.

Basic Commissioning

Switch the System Configuration

Explains how to check and change the system configuration based on machine tool structure.

Adjust I/O Port Polarity

Details adjusting input/output port polarities and clearing I/O port alarms for monitoring.

Set Commissioning Parameters

Guides on setting parameters for commissioning to prevent machine damage during movement.

Adjust the Axis Direction

Describes checking and adjusting the positive direction of each axis to prevent damage.

Return to the Machine Origin

Explains adjusting coordinate position before machining, using incremental or absolute encoders.

Set the Workbench Travel

Guides on defining valid machining stroke range for X, Y, Z axes to implement soft limits.

Quick Start

Load a Program File

Details loading program files from host, USB, or internet for machining.

Execute Tool Calibration

Explains measuring selected tools to ensure normal operation during machining.

Adjust the WCS

Guides on establishing a new coordinate system (WCS) by selecting a reference point on the workpiece.

Define the Workpiece Origin

Describes defining the workpiece origin relative to a fixed point on the workpiece.

Select Tools for Machining

Explains selecting specific tools from a program file for machining different parts.

Execute Selective Machining

Allows optional skipping of program file sections by customizing start/end lines for machining range.

Execute Machining

Details running the program from beginning to end or until an interruption.

FAQs (Operator)

Failed to Register the System

Addresses issues encountered when the system fails to register, providing troubleshooting steps.

Tool Calibration Overtravel Alarm

Explains causes and solutions for overtravel alarms during tool calibration.

Z-axis Overtravel Protection

Discusses potential causes and solutions for Z-axis overtravel protection issues.

FAQs (Manufacturer)

Axis Servo Alarm

Covers causes and solutions for axis servo alarms, often related to polarity or drive issues.

Failed to Register the System

Addresses manufacturer-related issues with system registration, offering solutions.

Drive 400 Alarm

Explains common causes and solutions for Drive 400 alarms, typically related to encoders or batteries.