Why is there no AC output from my Winco DE4040?
If there is no AC output from the Winco Portable Generator, this could be due to a defective diode, voltage regulator, rotor, or stator. Other possible causes include a defective exciter rotor or stator, an AC short in the output leads, a defective/open generator output breaker, or a wiring error.
What to do if Winco DE4040 engine won’t crank?
If the Winco Portable Generator engine won’t crank, this may be due to a low or dead battery, blown DC fuses, or a defective DSE 7310. Other potential causes include a defective key switch, loose or dirty battery terminals, a defective starter or start solenoid, a locked-up engine genset, a defective engine harness, or improper battery voltage to the start solenoid, fuel pump, or fuel solenoid.
Why does my Winco DE4040 Portable Generator engine start, then stop and alarm light comes on?
If the Winco Portable Generator engine starts, then stops and the alarm light comes on, the issue could stem from low engine oil pressure, high engine water temperature, or engine overspeed. It could also be due to the engine entering overcrank, no output from the AC generator, loss of speed signal, or loss of run signal.
Why is my Winco Portable Generator system difficult to start?
If the Winco Portable Generator system is difficult to start, it could be due to the compressor being flooded with oil, the system not being discharged, or the oil being too viscous. In all these cases verify engine speed is correct.
What to do if Winco Portable Generator unit will not crank when power fails?
If the Winco Portable Generator unit will not crank when power fails, potential causes include the digital genset not being in AUTO, the transfer control switch not being in the AUTOMATIC position, or incorrect wiring between the ATS and genset. Other possible reasons are a defective control relay in the ATS, blown fuse(s) in the DSE 7310, a defective DSE 7310, loose or dirty battery terminals, a defective starter or start solenoid, or a low/dead battery.
Why Winco DE4040 Portable Generator engine will not come up to speed after it starts?
If the Winco Portable Generator engine will not come up to speed after it starts, this could be due to insufficient fuel volume getting to the unit. Other possible causes include too small of a fuel line, fuel racks not opening properly, a defective governor, or an AC short in generator components.
Why does the safety valve blow off on my Winco DE4040 Portable Generator?
If the safety valve blows off on the Winco Portable Generator, it could be due to a defective safety valve, a soiled fine separator cartridge, or the system not relieving continuous operation. It may also occur if the system does not switch off automatically (drop-out mode), or due to freeze up of pressure switch because the compressor started before engine is fully warmed up.
What to do if Winco DE4040 Portable Generator engine cranks but will not start?
If the Winco Portable Generator engine cranks but does not start, possible causes include improper fuel delivery, a shut-off fuel supply, an empty fuel tank, or air in the fuel system. Other potential issues are a fuel solenoid that hasn't opened, a defective fuel pump or solenoid, a defective engine harness, or improper battery voltage to the fuel pump or fuel solenoid.
Why is there no or insufficient feed quantity from my Winco DE4040 Portable Generator?
If there is no or insufficient feed quantity from the Winco Portable Generator, this could be due to a soiled intake filter, an oil shortage, the intake control valve not opening, or leaks in the system.
Why Winco DE4040 Portable Generator system continually discharges, resulting in low feed quantity?
If the Winco Portable Generator system continually discharges and has a low feed quantity, possible causes include a defective solenoid valve, a defective relief valve, or a break in the electric supply line to the solenoid valve.
General| Brand | Winco |
|---|---|
| Model | DE4040 |
| Category | Portable Generator |
| Language | English |
To Next Page
