What to do if Worx WR165E Lawn Mower Landroid cannot dock?
If your Worx Landroid cannot correctly dock with the charging pile, it might be due to: * Environmental influences. Restart Landroid. * Poor connection caused by debris on the charging strip. Clean the contact pins located on the charging pile and the charging strip on Landroid using a cloth.
Why does Worx WR165E Lawn Mower run outside the boundary wire?
If your Worx Landroid runs outside the boundary wire, doesn't mow within a zone, or moves erratically near it, it could be due to: * The boundary wire of another Landroid or robotic mower being too close. Ensure at least 1m clearance between your boundary wire and any others. * Signal leakage in wet conditions where the wire has been joined or repaired incorrectly. Check boundary wire joints and insulate them for a waterproof connection. * Boundary wire electric signal leakage due to broken insulation. Repair damaged wire with the supplied connectors.
What to do if my Worx WR165E Lawn Mower charging time is too long?
If your Worx Lawn Mower takes longer to charge than expected, it could be due to debris on the charging strip causing a poor connection, or the charging protection program may be activated because of high temperature. Clean the contact pins on the charging pile and the charging strip on the Landroid with a cloth. Alternatively, place the charging station in a shady area or wait for the temperature to cool down.
Why does my Worx WR165E Landroid stop in the working area?
Your Worx Landroid stopping in the working area can be caused by: * An obstacle in the working area. Remove any obstacles. * The cutting height being set too low for the grass length or the grass being too dense. Raise the cutting height gradually. * The extended boundary wire exceeding 300m, which may cause signal problems. Reduce the length of the boundary wire. * The distance between the center of the lawn and the boundary wire exceeding 25m, potentially causing signal attenuation. Reduce this distance to within 25m.
Why is there a red light on my Worx WR165E Lawn Mower charging pile?
A red light on the Worx Lawn Mower charging pile indicates that the boundary wire isn’t connected. Check that the boundary wire has been connected correctly to the charging station and that there are no breaks in the boundary wire.
Why does my Worx WR165E Lawn Mower Landroid have shorter run times?
Shorter run times between charges for your Worx Landroid can be due to: * Clogging in the blade disc, creating friction. Take off the blade disc and clean it. Also, consider if the grass is too high or thick. * An unbalanced blade disc causing heavy shaking. Check the blade disc and blades, removing any debris. Replace the blades if necessary. * An exhausted or old battery. Replace the battery. * The working time is up, reset the working time.
Why is my Worx WR165E Lawn Mower cutting grass unevenly?
Uneven grass cutting with your Worx Lawn Mower can occur for several reasons: * The mower isn't operating enough hours daily. Try adding more hours to the mowing schedule. * The mowing area is too large for your Landroid model. Consider decreasing the mowing area or increasing the working time. * The blades are dull. Change all blades and screws to balance the blade disc. * The cutting height is too low for the grass length. Raise the cutting height gradually. * Grass or objects are wrapped around the blade disc. Inspect and remove any obstructions. * There's a grass build-up in the blade disc or motor frame. Ensure the blade disc rotates freely, removing any debris if needed.
What to do if Worx Lawn Mower turns on but blade disc does not spin?
If your Worx Lawn Mower turns on but the blade disc doesn't spin, it might be because the Landroid is searching for the charging station. This is normal behavior; the blade disc does not rotate while it's automatically searching for the charging station to recharge.
Why is there a red light on Worx WR165E charging pile?
A red light on the charging pile of your Worx Lawn Mower indicates that the boundary wire isn’t connected. Verify that the boundary wire is correctly connected to the charging station and that there are no breaks in the boundary wire.
Why Worx WR165E Lawn Mower LED light on charging pile does not turn on?
If the LED light on the charging pile of your Worx Lawn Mower doesn't turn on, it could be due to a lack of power. Check that the charging station is properly connected to the charger and that the charger is connected to a suitable power supply.
Read all warnings and instructions carefully. Failure to comply may result in injury.
Never operate with defective guards, keep hands/feet away from blades, avoid bad weather.
Switch off power for maintenance, keep fasteners tight, inspect weekly, use correct charger.
Do not dismantle, short-circuit, or expose battery to heat. Handle leaks safely.
Read manual before use. Keep safe distance. Do not ride on machine.
Lists common error messages and their initial troubleshooting steps.
General| Battery Voltage | 20 V |
|---|---|
| Battery Capacity | 2.0 Ah |
| Power Source | Battery |
| Cutting Height Adjustment | Central |
| Cutting System | Rotary Blade |
To Next Page
