Need help?Do you have a question about the XIEGU X5105 and is the answer not in the manual?
General| Type | Portable HF Transceiver |
|---|---|
| Frequency Range RX | 0.5-30 MHz |
| Antenna Impedance | 50 Ohms |
| Operating Modes | SSB, CW, AM, FM |
| Output Power | 5W |
| Power Supply | 9-15V DC |
| Current Drain RX | 500mA |
| Current Drain TX | 1.5A max |
| Receiver Sensitivity | 0.5μV (10dB S/N) |
| Interface | USB |
Describes the transceiver's output power and frequency range.
Highlights the device's small dimensions for portability.
Mentions the display type and size for user interface.
Details the battery capacity and voltage (3800mAh @ 12V).
States the inclusion of an automatic antenna tuner.
Notes the digital baseband for advanced features.
Features direct decoding of common amateur radio data modes.
Mentions the high-stability temperature compensated crystal oscillator.
Lists supported CW, PSK, RTTY functions.
Allows direct data communication without PC or modem.
Supports manual and auto telegram key modes.
Indicates a broad range of operating voltages.
Covers Power, MODE, PRE/ATT, RIT, NB, LOCK, UP, DN, Po keys.
Covers V/M, A/B, <, >, ATU keys.
Covers Volume keys and PTT key.
Covers T/R, DATA, LINK indicators.
BNC type interface with 50-ohm impedance.
For outputting and receiving medium frequency signals.
3.5mm stereo socket for connecting earphones.
External DC power input, 13.8V@3A, for charging.
8-core mini-DIN for external amplifier, PTT, data.
3.5mm stereo for manual/auto telegram keys.
3.5mm interface for external antenna tuner.
3.5mm interface for computer control and firmware update.
Connects to the attached multi-function handheld microphone.
Covers LOCK, PTT, Up/down, FIL, MODE, V/M, TUNER keys.
Indicates transceiver and function status.
The main button layout on the microphone.
Custom settings keys (F1/F2).
Details pins and usage for these interfaces.
ACC pins and CW key connection diagram.
Steps for charging and onscreen indicators.
Notes on battery lifespan and voltage/heating safety.
Specs and correct connection for power.
EMC rings and warranty exclusions.
Explains menu structure and navigation using keys and knob.
Covers PTT, Volume, MODE, NB, PRE/ATT, Po, UP/DN keys.
Covers RIT, V/M, A/B, <, >, ATU keys.
Covers AGC, RF-GAIN, SQL, COMP, DSP-FIL, NR, NOTCH, EQ.
Covers MEMO, MSG, CALLSIGN, KEY, TONE, QSK.
Covers DIGI, SRM, SWR, MIC/VOX, SPK, PTT.
Procedures for powering the transceiver on and off.
Instructions for performing a hard reset if the system crashes.
Use NB key to toggle between battery level and voltage display.
Covers range, bands, and switching methods.
Details the sequence for selecting modes like LSB, USB, CW.
Using volume+/- keys to control audio output.
Using the Po key and knob to set power from 0.1W to 5W.
Recommends minimizing power when first using the device.
How to use the PTT key for transmitting and communication.
Explains normal mode and triggering mode for PTT.
Using [<] and [>] keys with knob, or [F-INP ENT] for direct input.
Connecting and initiating auto-tuning via the ATU key.
Antenna icon status and SWR checks.
Pressing RIT key and using knob to shift frequency.
Long-pressing RIT key to reset deviation.
Cycling through modes and advice for different conditions.
Using PRE for weak signals and ATT for strong signals.
Sequence of PRE, ATT, OFF states.
Overview of NB purpose and how to enable it.
Switching between VFO-A and VFO-B.
Setting different frequencies for receiving and transmitting.
Using the V/M key to switch modes.
Long press LOCK key to enable/disable lock.
Short press LOCK key to adjust brightness levels.
Steps for CW setup and using trainer mode.
Using menu 3 for editing and sending preset messages.
Operations for channel memory and naming.
Connecting to computer, software setup, and EMC.
Navigating and changing parameters like LCD, volume, etc.
Covers Band Stack, MIC Bias, Charger, IF Output, RSSI, Key customization.
Using standard CIV sets for remote control.
Provides wave band voltage data for frequency bands.
Lists frequency range, modes, impedance, etc.
Details IF, sensitivity, selectivity, audio.
Lists main machine, microphone, cables, manual, etc.
Lists CE-19 and XPA125B accessories.
Shows connection via CE-19 and ACC interface.
Diagrams for X108G and X108.
Details PTT CON, TO XPA125, AF CON, DATA CON functions.
States copyright and reservation of rights.
To Next Page
