EasyManua.ls Logo

Xtralis ICAM IAS-2 - User Manual

Xtralis ICAM IAS-2
38 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Xtralis ICAM IAS-2
Product Guide
July 2010
Document Number: 14942_05
Part Number: 29301

Table of Contents

Other manuals for Xtralis ICAM IAS-2

Preview: Commissioning Guide
Commissioning Guide26 pages

Questions and Answers

  • A
    Angela BrownJul 25, 2025
    What to do if my Xtralis ICAM IAS-2 Smoke Alarm detectors are unresponsive to smoke tests?
    • B
      Brittany ThompsonJul 25, 2025
      If the detectors of your Xtralis Smoke Alarm are not responding to smoke tests, verify that the sampling pipe is correctly installed and undamaged. Also, ensure that the holes and pipe length do not exceed the specified limits for the detector. Confirm that the recommended baffles are fitted and that you're using the recommended test method. As a final step, try increasing the fan speed and re-testing.
  • K
    Katherine SmallJul 29, 2025
    Why is the FLOW HI or FLOW LO light on my Xtralis ICAM IAS-2 Smoke Alarm?
    • R
      Ryan MorrisonJul 29, 2025
      If the FLOW HI or FLOW LO light is illuminated on your Xtralis Smoke Alarm, make sure the sampling pipes are correctly installed, the lid is fitted, and the box is fully sealed. Also, ensure the flow calibration procedure has been carried out. Finally, check that the filters are clean.
  • T
    trobinsonAug 3, 2025
    Why is the flow reading on the Bargraph display of my Xtralis ICAM IAS-2 moving erratically?
    • S
      Suzanne AllenAug 3, 2025
      If the flow reading on the bargraph display of your Xtralis Smoke Alarm moves erratically, decrease the flow sensitivity setting and recalibrate the air flows.
  • T
    tammy55Aug 7, 2025
    What to do if the flow reading on Bargraph of Xtralis ICAM IAS-2 Smoke Alarm is unresponsive to broken/blocked pipe?
    • L
      lambertcoreyAug 7, 2025
      If the flow reading on the bargraph of your Xtralis Smoke Alarm is unresponsive when the pipe is broken or blocked, increase the flow sensitivity setting and recalibrate the air flows.
  • J
    jenkinsandrewAug 12, 2025
    How to fix Xtralis ICAM IAS-2 Smoke Alarm when there are no lights on display and fan not running?
    • K
      Keith PowellAug 12, 2025
      If there are no lights on the display and the fan is not running on your Xtralis Smoke Alarm, ensure the supply leads are correctly oriented and that the BAT FUSE is correctly seated in the socket and the fuse is not blown.
  • G
    Garrett HerreraAug 16, 2025
    What to do if there are no lights on display but fan running on Xtralis ICAM IAS-2?
    • S
      Stephanie JohnsonAug 16, 2025
      If there are no lights on the display but the fan is running OK on your Xtralis Smoke Alarm, ensure the ribbon cable is fully seated into the main and display boards.
  • J
    jamiedeanAug 20, 2025
    How to stop power light flashing on Xtralis ICAM IAS-2 Smoke Alarm?
    • T
      Travis BrownAug 20, 2025
      Ensure the supply to the BATTERY connector of your Xtralis Smoke Alarm is within the specified limits if the power light is flashing.

Summary

Wiring

Field Connections

Describes the connection points for wiring the unit.

Point Detectors

Detector Installation

Instructions for mounting point detectors on the unit.

Wiring Examples

Pipe Installation

Pipe Specification

Standard Configurations

Set-up

Display Functions

User Functions

Details on how to access and use system functions.

Set-up Notes

Testing

Detectors

System

Method for testing the overall system functionality.

AS 1603.8 Listed Detectors

Sampling Pipe Network Design

Guidance on designing sampling pipe networks for compliance.

Problem Solving

Specifications

Typical Supply Current & Fan Speed

Xtralis ICAM IAS-2 Specifications

General IconGeneral
TechnologyAspirating Smoke Detection (ASD)
Number of Sampling Pipes2
Alarm ThresholdsConfigurable
Operating Voltage24 VDC
Power Supply24 VDC
Operating Humidity10% to 95% RH (non-condensing)
IP RatingIP30
Detection PrincipleLaser light scattering
Operating Temperature-10°C to +55°C
Humidity Range10% to 95% RH
CertificationsUL, FM, VdS, LPCB

Related product manuals