Xtralis ICAM IAS-2 Commissioning Guide

Xtralis ICAM IAS-2

26 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

ICAM

Commissioning Guide

May 2018

Document: 14972_02

Part Number: 29303

Table of Contents

Other manuals for Xtralis ICAM IAS-2

Product Guide38 pages

Questions and Answers:

A
Angela BrownJul 25, 2025
What to do if my Xtralis ICAM IAS-2 Smoke Alarm detectors are unresponsive to smoke tests?
- B
  Brittany ThompsonJul 25, 2025
  If the detectors of your Xtralis Smoke Alarm are not responding to smoke tests, verify that the sampling pipe is correctly installed and undamaged. Also, ensure that the holes and pipe length do not exceed the specified limits for the detector. Confirm that the recommended baffles are fitted and that you're using the recommended test method. As a final step, try increasing the fan speed and re-testing.
K
Katherine SmallJul 29, 2025
Why is the FLOW HI or FLOW LO light on my Xtralis ICAM IAS-2 Smoke Alarm?
- R
  Ryan MorrisonJul 29, 2025
  If the FLOW HI or FLOW LO light is illuminated on your Xtralis Smoke Alarm, make sure the sampling pipes are correctly installed, the lid is fitted, and the box is fully sealed. Also, ensure the flow calibration procedure has been carried out. Finally, check that the filters are clean.
T
trobinsonAug 3, 2025
Why is the flow reading on the Bargraph display of my Xtralis ICAM IAS-2 moving erratically?
- S
  Suzanne AllenAug 3, 2025
  If the flow reading on the bargraph display of your Xtralis Smoke Alarm moves erratically, decrease the flow sensitivity setting and recalibrate the air flows.
T
tammy55Aug 7, 2025
What to do if the flow reading on Bargraph of Xtralis ICAM IAS-2 Smoke Alarm is unresponsive to broken/blocked pipe?
- L
  lambertcoreyAug 7, 2025
  If the flow reading on the bargraph of your Xtralis Smoke Alarm is unresponsive when the pipe is broken or blocked, increase the flow sensitivity setting and recalibrate the air flows.
J
jenkinsandrewAug 12, 2025
How to fix Xtralis ICAM IAS-2 Smoke Alarm when there are no lights on display and fan not running?
- K
  Keith PowellAug 12, 2025
  If there are no lights on the display and the fan is not running on your Xtralis Smoke Alarm, ensure the supply leads are correctly oriented and that the BAT FUSE is correctly seated in the socket and the fuse is not blown.
G
Garrett HerreraAug 16, 2025
What to do if there are no lights on display but fan running on Xtralis ICAM IAS-2?
- S
  Stephanie JohnsonAug 16, 2025
  If there are no lights on the display but the fan is running OK on your Xtralis Smoke Alarm, ensure the ribbon cable is fully seated into the main and display boards.
J
jamiedeanAug 20, 2025
How to stop power light flashing on Xtralis ICAM IAS-2 Smoke Alarm?
- T
  Travis BrownAug 20, 2025
  Ensure the supply to the BATTERY connector of your Xtralis Smoke Alarm is within the specified limits if the power light is flashing.

Xtralis ICAM IAS-2 Specifications

General

Technology	Aspirating Smoke Detection (ASD)
Number of Sampling Pipes	2
Alarm Thresholds	Configurable
Operating Voltage	24 VDC
Power Supply	24 VDC
Operating Humidity	10% to 95% RH (non-condensing)
IP Rating	IP30
Detection Principle	Laser light scattering
Operating Temperature	-10°C to +55°C
Humidity Range	10% to 95% RH
Certifications	UL, FM, VdS, LPCB

Related product manuals

Preview: Xtralis ICAM IAS-1

Xtralis ICAM IAS-1

Preview: Xtralis ICAM IFT

Xtralis ICAM IFT

Preview: Xtralis ICAM IFT-P

Xtralis ICAM IFT-P

Xtralis ICAM IFT-1

Xtralis ICAM IFT-4

Xtralis ICAM IFT-6

Preview: Xtralis ICAM ILS-2

Xtralis ICAM ILS-2

Xtralis ICAM IFT-15

Xtralis ICAM IFT-4-NF

Preview: Xtralis VESDA

Preview: Xtralis VESDA-E VEP-1P

Xtralis VESDA-E VEP-1P

Preview: Xtralis VESDA E-Series

Xtralis VESDA E-Series