To Next PageTo Next PageWhat to do if there is no sound from my Yamaha CD Player?
If you're not getting any sound from your Yamaha CD Player, check the output cable connections to ensure they are properly connected and not defective. Also, verify that your amplifier controls are set to the correct input selection. If you have a CDX-497 model, make sure the OUTPUT LEVEL +/– buttons are not set at minimum; adjust the volume accordingly.
Why is my Yamaha CDX-397 CD Player remote control not working?
If the Yamaha CD Player remote control isn't working, the batteries might be weak, so try replacing them. Also, make sure you're within 6 meters and a 60° radius of the unit. Direct sunlight or certain types of lighting can also interfere with the remote control sensor, so try repositioning the main unit.
Why does the sound skip on my Yamaha CD Player?
If the sound skips on your Yamaha CD Player, it could be due to vibrations or impacts affecting the unit. Try relocating the unit to a more stable surface. Additionally, a dirty disc can cause skipping, so clean the disc carefully.
How to fix a Yamaha CDX-397 CD Player that does not turn on?
If your Yamaha CD Player doesn't switch on when you press the power button, make sure the power cord is securely and completely connected.
What to do if my Yamaha CDX-397 CD Player playback does not start?
If playback doesn't start on your Yamaha CD Player, check the disc for damage and replace it if necessary. If there is moisture on the laser pickup, wait 20 to 30 minutes after switching the unit ON before trying again. Ensure the disc is loaded with the label side up and that it's clean. If using a CD-RW, make sure it's correctly recorded and playable with this unit. Also, make sure that the disc is a standard disc playable with this unit.
Why does my Yamaha CDX-397 sound hum?
If your Yamaha CD Player is humming, ensure the audio cables are securely connected. If the problem continues, the cables may be defective and need replacement.
What to do if the Yamaha CDX-397 CD Player disc tray does not close?
If the disc tray on your Yamaha CD Player doesn't close completely, check for any foreign objects obstructing the tray and carefully remove them.
Why is the playback delayed on my Yamaha CDX-397?
If playback on your Yamaha CD Player is delayed or starts at the wrong place, the disc may be scratched or damaged. Check the disc carefully and replace it if needed.
How to reduce noise from tuner on Yamaha CDX-397?
To reduce noise from a nearby tuner affecting your Yamaha CD Player, move the tuner and the main unit farther apart.
What to do if TV functions strangely when Yamaha CDX-397 CD Player remote is used?
If your TV functions strangely when using the Yamaha CD Player remote, the remote might be interfering with the TV's remote control sensor. Try relocating the main unit away from the TV or cover the TV’s remote control sensor.
General| Type | CD Player |
|---|---|
| Frequency Response | 2 Hz - 20 kHz |
| Signal-to-Noise Ratio | 105 dB |
| Dynamic Range | 96 dB |
| Output Level | 2.0 V |
| Digital Output | Coaxial |
| Power Consumption | 15 W |
| Total Harmonic Distortion | 0.003% (1 kHz) |
Lists important safety instructions for operating the unit.
Warns about laser radiation and electrical shock risks.
Specific guidance for U.K. customers regarding the power plug.
Details on playing MP3 and WMA files and disc compatibility.
Explains the MP3 and WMA audio formats and their specifications.
Instructions for installing and replacing remote control batteries.
Specifies the operating range and potential interference issues for the remote.
Guides on connecting the unit to an amplifier via analog or digital outputs.
Instructions on connecting the unit to the AC power outlet.
Identifies and describes controls on the player's front panel.
Explains the various indicators and information shown on the display.
Identifies the remote control component.
Details the function of each button on the remote control.
Explains how to use numeric and cursor buttons for navigation and input.
Steps to turn on the unit, open/close tray, and load a disc.
How to pause, stop, resume playback and select tracks or files.
How to navigate folders/files and use skip/search functions.
Explains the various display options for audio CDs.
Explains the display options for MP3 and WMA discs.
How to play a single track or selected folder repeatedly.
How to repeat the entire disc playback.
How to set start/end points and cancel the Repeat A-B function.
Steps to program tracks in a desired order for playback.
Explains the information displayed during the programming process.
How to stop, clear, or correct programmed tracks.
How to start playback from an index number and how to cancel the function.
Automatically programs tracks for tape recording based on disc order.
Steps to manually select tracks for Side A of the tape.
Steps to manually select tracks for Side B of the tape.
Programs tracks in random order for tape recording.
How to find the peak audio level for tape recording adjustment.
How to stop the peak level search function.
Steps for synchronizing CD playback with tape deck recording.
How to stop or cancel the CD synchronized recording.
Information on discs compatible with the unit.
Best practices for handling and caring for compact discs.
Warnings against using incompatible or damaged discs.
Solutions for issues like unit not turning on or playback not starting.
Solutions for problems related to sound, skips, hums, and external noise.
Solutions for remote control malfunctions and TV interference.
Technical details of the audio performance.
General power, dimensions, weight, and laser properties.
