Yamaha DS55 - MIDI Data Format; Transmission Conditions; Transmission Data

MIDI DATA FORMAT
1. Transmission Conditions
Note on/off $IN
Modulation wheel
Breath control
Volume pedal
Sustain switch
$Bn , $01
Sn, 802-— a
SB Ml a A a E
$20,940 et
midi ch
Pitch bender Ste O—O— > MIDI out
midi sw
Program change Sin
Data entry (inc) $bn,$60———__ Play mode
Data entry (dec) $Bn,$61 O
on/off
Active sensing $FE-
aok (bulk dump) Pano becas
Voice edit buffer $F0,$43,$0s ,$03
Packed 32 Voice
Additional edit bufferl $F0,843,$0s,$7e
DELAY BFO, $43, $0s , $76
SYSTEM
IN (7 y Pta
arameter change
System set up $F0,$43,$1s,525
$FO,$43,$0s ,§04-——— 4
$F0,$43, $08 ,87e ——_
exclusive on/off
Delay BFO,$43,$1s,$25-—_J
Master tuning $FO,$43,$1s,510,87b, $00
System PFM 8F0,$43,$1s,81¢-——— EE E
Bulk block SFO, $43,315 ,$24 O = on/off sw
2. Transmission Data
2-1 Channel Information
(1) Channel Voice Message
1) NOTE ON/OFF
STATUS 100Innnn (9n) n-channel number
NOTE No. Okkkkkkk k=36 (C1) ~96(C6)
VELOCITY Ovvvvvvv (V0) NOTE ON
00000000 (Y=0) NOTE OFF
2) CONTROL CHANGE
STATUS 1011nnnn (Bn) n=channel number
CONTROL No. OCCCCCCe
CONTROL VALUE ` OVVVVVVV
REH CONTROL NUMBER `
C=1 Modulation wheel v=0—127
C=2 Breath control v=0~ 127
C7 Foot volume v=0~ 127
C=64 Sustain switch
C=96 Data entry switch inc
C=97 Data entry switch dec
3) PROGRAM CHANGE
v=0:off,127:on
v=127:0n (Play mode only)
v=127:0n (Play mode only)
STATUS 1100nnnn (Cn) n=channel number
PROGRAM No. Oppppppp p=0~99
4) PITCH BENDER
STATUS 1110nnnn (En) n=channel number
VALUE (LSB) Ouuuuuuu
VALUE (MSB) Ovvvvvvv
Resolution: 7bit
Transmitted data is shown below.
BEE MSB © o == LSB >
0000 0000 (00) 0000 0000 (00) Minimum value
0100 0000 (40) 0000 0000 (00) Center value
0111 1111 (7F) 0111 1110 (7E) Maximum value
2-2 System Information
(1) System Realtime Message
1) ACTIVE SENSING
STATUS 11111110 (FE)
(2)System Exclusive Message
1) PARAMETER CHANGE
STATUS
ID No.
SUB STATUS
GROUP NUMBER
PARAMETER No.
DATA
EOX
11110000
01000011
0001ssss
Oggegghh
Oppppppp
Oddddddd
11110111
(FO)
(43)
(Is) s-Transmit channel
g-Group number
h=Sub group number
(F7)
The 5 parameter group numbers and parameteer numbers used
are described be
Type
low.
Number of Data Bytes
SYSTEM SET UP
SYSTEM PFM
DELAY
MASTER TUNING
BULK BLOCK
2) BULK DUMP
STATUS
ID No.
SUB STATUS
GROUP NUMBER
BYTE COUNT(MSB)
BYTE COUNT(LSB)
DATA
DATA
CHECK SUM
EOX
11110000
01000011
0000ssss
ofififff
Obbbbbbb
Obbbbbbb
Oddddddd
Oddddddd
Oeeeeeee
11110111
(FO)
(43)
(0s) s=Transmit channel
i-Format number
(F7)
The 2 type of format numbers used are described below.
Type
Byte Count
VOICE EDIT BUFFER
PACKED 32 VOICE
3) UNIVERSAL BULK DUMP
STATUS
ID No.
SUB STATUS
GROUP NUMBER
BYTE COUNT(MSB)
BYTE COUNT(LSB)
CLASSIFICATION-
NAME
DATA FORMAT-
NAME
DATA
DATA
CHECK SUM
EOX
11110000
01000011
0000ssss
01111110
Obbbbbbb
Obbbbbbb
01001100
01001101
00100000
00100000
Ommmmmmm
Ommmmmmm
Oddddddd
Oddddddd
Oeeeecee
11110111
s=Transmit channel
ASCIT?L
ASCID'M
ASCII”
ASCII’
(F7)
The 3 type of format used are described below.
Type
SYSTEM
DELAY
ADDITIONAL EDIT
BUFFER 1
8054S
8054DL
8976AE
Add-1