Yamaha HTR-5250 User Manual (English)

Other manuals for Yamaha HTR-5250

Questions and Answers:

C
Caitlin ShawJul 30, 2025
What to do if there is no sound or picture on my Yamaha HTR-5250 Receiver?
- J
  Jessica BowersJul 30, 2025
  If you're experiencing a lack of sound or picture with your Yamaha Receiver, here are a few things to check: * Ensure all input and output cables are correctly connected and not defective. * Verify that you've selected the appropriate input source using the INPUT SELECTOR or TAPE/MD MON / EXT. DECODER. * Make sure the speaker connections are secure. * Confirm that SPEAKERS are set to the ON position corresponding to the speakers you're using. * Check that the sound isn't muted by adjusting the VOLUME and pressing MUTE. * Ensure that the input source signals are compatible with the unit (PCM audio, Dolby Digital, or DTS).
W
Willie CallahanAug 5, 2025
What to do if the sound suddenly goes off on my Yamaha HTR-5250 Receiver?
- E
  Elizabeth WallaceAug 5, 2025
  If the sound on your Yamaha Receiver suddenly cuts off, it could be due to a couple of reasons: * The protection circuit might have been activated due to a short circuit. To resolve this, set the unit to standby mode and then turn it back on to reset the protection circuit. * Alternatively, the SLEEP timer may have activated. If so, simply turn the power back on and play the source again.
S
Sherry Brown DDSAug 11, 2025
Why won't my Yamaha HTR-5250 turn on?
- L
  lmillerAug 12, 2025
  If your Yamaha Receiver fails to turn on or enters standby mode shortly after being powered on, check the following: * Ensure the power cord is firmly connected to both the receiver and the power outlet. * Verify that the IMPEDANCE SELECTOR switch on the rear panel is fully set to either the right or left position when the unit is in standby mode. Make sure that you firmly connect the power cord and set the switch fully to the right or left position when the unit is in the standby mode.
K
kathryn27Aug 17, 2025
Why can I only hear sound from one speaker on my Yamaha HTR-5250?
- T
  Taylor BakerAug 17, 2025
  If you're only hearing sound from one speaker connected to your Yamaha Receiver, the issue might be due to incorrect cable connections or an incorrect BALANCE setting. * Ensure that all cables are properly connected. If the problem continues, the cables may be defective. * Check the BALANCE setting and adjust it to the appropriate position.
C
Christopher CharlesAug 23, 2025
Why is there no sound from the effect speakers on my Yamaha HTR-5250?
- O
  orochaAug 25, 2025
  If you're not getting any sound from the effect speakers on your Yamaha Receiver, consider these potential causes: * The sound effect might be turned off. Press the EFFECT button to turn it on. * You might be using a Dolby Surround, Dolby Digital, or DTS decoding DSP program with material that isn't encoded with those formats. Try selecting another DSP program.

Yamaha HTR-5250 Specifications

General

Type	AV Receiver
Channels	5.1
Frequency Response	20 Hz - 20 kHz
Input Impedance	47 kOhms
Input Sensitivity	200 mV
Signal to Noise Ratio	100 dB
Speaker Load Impedance	8 ohms
Digital Inputs	2 Optical, 1 Coaxial
Surround Sound Formats	Dolby Digital, DTS
Video Inputs	2 S-Video
Video Outputs	1 Composite, 1 S-Video
Dimensions (W x H x D)	435 x 151 x 363 mm
Power Output (per channel)	100W (8 ohms, 20Hz-20kHz, 0.09% THD)