Yamaha HTR-6230 User Manual

39 En
Remote control features
English
INTRODUCTION
ADDITIONAL
INFORMATION APPENDIX
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
You can control other components by setting the
appropriate remote control codes. For a complete list of
available remote control codes, refer to “List of remote
control codes” at the end of this manual.
Remote control code default settings
Note
• You may not be able to operate your Yamaha component even if a
Yamaha remote control code is preset as listed above. In this case, try
setting another Yamaha remote control code.
1 While pressing and holding one of the input
selector buttons (f) on the remote control to
select the input area you want to set up,
press bAV POWER for more than 3
seconds.
2 Press the numeric buttons (0 to 9) (y) to
enter the four-digit remote control code for
the component to be used.
When the setting succeeds, “RemoteSetup OK”
appears; however, when it dues not, “RemoteSetup
NG” appears on the front panel display.
Notes
• If the manufacturer of your component has more than one code, try each
of them until you find the correct one.
• If you do not press any buttons within 30 seconds in step 2, the setup
process is canceled. If this happens, repeat the setup procedure.
■ Resetting all remote control codes
Use this feature to clear all the remote control codes
previously set and reset all of them to the initial factory
settings.
1 While pressing and holding hAMP, press
bAV POWER for more than 3 seconds.
2 Press the numeric buttons (y) to enter the
code number “9981.”
“RemoteSetup OK” appears on the front panel
display, and the remote control codes previously set
are cleared and reset to the initial factory settings.
y
• If you do not press any buttons within 30 seconds after step 1, the
clearing process is canceled. In this case, repeat the clearing
procedure.
Setting remote control codes
Input
source
Component
category
Manufacturer
Default
code
CD CD Yamaha 5013
MD/CD-R CD-R Yamaha 5001
TUNER TUNER Yamaha 5007
DVD DVD Yamaha 2000
DTV/CBL — — —
V-AUX/
DOCK
TUNER Yamaha 5011
DVR DVR Yamaha 2011
A TUNER Yamaha 5012
B TUNER Yamaha 5009
C TUNER Yamaha 5017
D— ——
E— ——
DVD
V-AUX/DOCK
D E
DTV/CBL DVR
CD MD/CD-R TUNER
A B C
POWER
AV
While holding down
Press for 3 seconds
POWER
AV
AMP
While holding down
Press for 3 seconds

Yamaha HTR-6230 Specifications

General

Channels	7.1
HDMI Inputs	4
HDMI Outputs	1
Dolby Digital	Yes
DTS	Yes
FM/AM Tuner	Yes
Response Bandwidth	10 Hz - 100 kHz
Signal-To-Noise Ratio	100 dB
Input Impedance	47 kOhm
Input Sensitivity	200 mV
Audio D/A Converter	192kHz/24-bit
Built-in Decoders	Dolby Digital, DTS, Dolby Pro Logic II
Surround System Class	7.1 channel
Digital Sound Processor (DSP)	Yes
DSP Preset Qty	17
Tuner Bands	AM/FM
Preset Station Qty	40
HDMI Switching	Yes
Frequency Response	10 Hz - 100 kHz
Power Output	100 W per channel
Amplifier Output Details	100W per channel (8 ohms, 20Hz-20kHz, 0.09% THD)
Surround Sound Effects	Cinema DSP
Additional Features	iPod compatibility
Tuning Range	FM: 87.5 - 108 MHz, AM: 530 - 1710 kHz
Connector Type	HDMI
Amplifier	Yes
Video Inputs/Outputs	Composite video
Audio Inputs/Outputs	4 x Audio line-in, 2 x Audio line-out
Digital Audio Inputs	2 optical, 1 coaxial