Why is only one speaker working on my Yamaha R-N301 Receiver?
First, check the cable connections to ensure they are correct and not defective. If the cables are properly connected, verify the speaker balance setting in the “Setup” menu and adjust it to the appropriate position.
How to fix noisy FM stereo reception on Yamaha R-N301?
Check the antenna connections. Try using a high-quality directional FM antenna. Alternatively, switch to monaural mode.
Why does my Yamaha Receiver have no sound?
Check that all input and output cables are properly connected and are not defective. Ensure you've selected the correct input source using the INPUT selector on the front panel or the remote control. Verify that the SPEAKERS A/B switches are correctly set and speaker connections are secure. Also, confirm that the output isn't muted and that the Max or Initial volume isn't set too low. Make sure the component corresponding to the selected input source is turned on and playing. If using a digital audio input (COAXIAL/OPTICAL), ensure the connected device's audio output is set to PCM.
What causes buzzing and whining noises in my Yamaha Receiver?
If you're experiencing buzzing and whining noises with your Yamaha Receiver, a TV set being used nearby may be the cause. Try moving the unit away from the TV set.
What causes continuous crackling and hissing noises on my Yamaha R-N301?
Continuous crackling and hissing noises on your Yamaha Receiver may result from interference from lightning, fluorescent lamps, motors, thermostats, or other electrical equipment. Try using an outdoor antenna and a ground wire to help reduce the noise, but it's difficult to eliminate all noise completely.
What to do if my Yamaha R-N301 Receiver does not detect the PC?
If your Yamaha Receiver isn't detecting your PC, first ensure the media sharing setting is correctly configured and the unit is selected as a device for sharing music. Check the settings of any security software on your PC that might be blocking access. Verify that both the unit and PC are on the same network, checking connections and router settings. Finally, if the MAC address filter is enabled on the unit, disable it or specify your PC's MAC address in the Setup menu.
What to do if my Yamaha R-N301 network feature does not function?
If the network feature on your Yamaha Receiver isn't working, ensure that the network parameters (IP address) have been obtained properly. Enable the DHCP server function on your router and set “DHCP” in the “Setup” menu to “On” on the unit. If manually configuring, verify you're using an IP address not used by other devices on your network.
What to do if Yamaha Receiver firmware update via the network is failed?
It may not be possible depending on the condition of the network, so update the firmware via the network again.
What to do if Yamaha R-N301 Receiver sound suddenly goes off?
This issue may occur if the protection circuitry has been activated due to a short circuit. In this case, set the speaker impedance to match your speakers. Also, ensure that the openings on the top panel of the unit are not blocked, as overheating can cause this. Finally, check if the auto power standby function is enabled; if so, adjust the setting to a longer duration or disable it in the “Option” menu.
What to do if my Yamaha R-N301 Receiver power does not turn on?
First, ensure the power cable is firmly connected. If the issue persists, check that the speaker wires aren't touching each other, as the protection circuitry may have been activated due to a short circuit. If the unit has been exposed to a strong electric shock, set it to standby, disconnect the power cable for 30 seconds, then reconnect and try again. If the protection circuitry has been activated three times consecutively, contact your nearest Yamaha dealer or service center to request repair.
General| Receiver type | stereo |
|---|---|
| Audio output channels | 2.0 channels |
| Signal-to-Noise Ratio (SNR) | 100 dB |
| Total Harmonic Distortion (THD) | 0.2 % |
| Power output per channel (1KHz@8 Ohm) | 140 W |
| Power output per channel (20-20KHz@8 Ohm) | 100 W |
| HDMI in | 0 |
| Digital audio optical in | 1 |
| Speakers connectivity type | - |
| Audio formats supported | AAC, FLAC, MP3, WAV, WMA |
| Video formats supported | MPEG4 |
| Wi-Fi | No |
| Ethernet LAN | Yes |
| Supported radio bands | AM, FM |
| Preset stations quantity | 40 |
| Audio input | 6 |
| Product color | Silver |
| Apple docking compatibility | Not supported |
| Power consumption (standby) | 0.1 W |
Weight and Dimensions| Depth | 333 mm |
|---|---|
| Width | 435 mm |
| Height | 141 mm |
| Weight | 6950 g |
Explains the layout and purpose of each control on the unit's front panel.
Instructions for connecting external speakers and various audio input devices.
Comprehensive steps to select an input source and start audio playback.
Procedure for tuning to FM and AM radio stations and optimizing reception.
Guide to setting up a Pandora account for using the personalized radio service.
Detailed guide for configuring network settings like IP address, MAC filter, and DMC control.
Procedures for downloading and installing new firmware for the unit.
Solutions for common issues related to power, sound output, and general operation.
Specific troubleshooting steps for when the remote control does not function correctly.
Addresses problems with FM/AM radio reception, tuning, and sound quality.
Solutions for network connectivity issues, PC detection, and failed firmware updates.
To Next Page
