Yamaha R-N500 User Manual (English)

Other manuals for Yamaha R-N500

Owner's Manual420 pages

Service Manual100 pages

Questions and Answers:

K
Kimberly GarrettAug 18, 2025
Why is there no sound coming from my Yamaha R-N500?
- J
  Joshua DeleonAug 18, 2025
  Several factors could be the reason for the lack of sound from your Yamaha Receiver. Ensure that all input and output cables are correctly connected; if the issue remains, the cables might be faulty. Verify that you've selected the appropriate input source using the INPUT selector on the front panel or the remote control. Also, check that the SPEAKERS A/B switches are correctly set. Confirm that your speaker connections are secure and that the output isn't muted. Finally, ensure that the Max or Initial volume settings aren't set too low. Also, confirm that the component corresponding to the selected input source is turned on and playing. If you're using a digital audio input (COAXIAL 1-2/ OPTICAL 1-2 jacks), ensure the connected device's audio output is set to PCM.
S
Stephanie PetersonAug 20, 2025
What to do if my Yamaha R-N500 Receiver fails to turn on?
- K
  kelly05Aug 20, 2025
  If your Yamaha Receiver isn't turning on, first ensure the power cable is firmly connected. If that doesn't work, check that the speaker wires are not touching each other. If the protection circuitry has been activated because of a short circuit, turn the power off and back on. If the unit has been exposed to a strong external electric shock, set it to standby mode, disconnect the power cable, plug it back in after 30 seconds, and then use it normally. Also, ensure the impedance setting matches your speakers.
M
Mrs. Amanda Howard DVMAug 22, 2025
Why does the sound on my Yamaha R-N500 suddenly go off?
- B
  brendanmeadowsAug 23, 2025
  The sound on your Yamaha Receiver might suddenly cut off due to several reasons. The protection circuitry might have been activated because of a short circuit. In this case, set the speaker impedance to match your speakers. Another possibility is that the unit has become too hot; ensure that the openings on the top panel are not blocked. Finally, the auto power standby function might have turned the unit off. You can change the auto power standby setting to a longer duration or disable it in the SETUP menu.
A
Andrea GreeneAug 26, 2025
How to fix noisy FM stereo reception on Yamaha R-N500?
- L
  Leroy CooperAug 26, 2025
  Noisy FM stereo reception on your Yamaha Receiver can often be improved. First, check the antenna connections. If the transmitter is too far away or the antenna input is poor, try using a high-quality directional FM antenna. Alternatively, switch to monaural mode.
M
Maria FernandezAug 27, 2025
What to do if only one speaker works on my Yamaha Receiver?
- L
  lfieldsAug 27, 2025
  If you're only hearing sound from one speaker on your Yamaha Receiver, start by checking the cable connections to ensure they are properly connected. If the problem persists, the cables may be defective. Also, verify the BALANCE control is set to the appropriate position.
T
taylor69Aug 30, 2025
Why is the network feature not working on my Yamaha R-N500?
- J
  Jessica DavisAug 30, 2025
  If the network feature on your Yamaha Receiver isn't functioning, it might be due to improperly obtained network parameters (IP address). Enable the DHCP server function on your router and set 'DHCP' in the 'SETUP' menu to 'On' on the unit. If you want to configure the network parameters manually, check that you are using an IP address which is not used by other network devices in your network.
K
Kirsten HuynhSep 1, 2025
What to do if Yamaha R-N500 Receiver cannot tune in station automatically?
- Y
  ywilsonSep 1, 2025
  If your Yamaha Receiver cannot tune in the desired station automatically, the signal might be too weak. Try using a high-quality directional FM antenna. Alternatively, try using the manual tuning method.
K
Kimberly HurleySep 4, 2025
What to do if firmware update fails on Yamaha R-N500 Receiver?
- J
  John ShafferSep 4, 2025
  If a firmware update fails via the network on your Yamaha Receiver, try updating the firmware via the network again or use a USB memory device.
S
Shelby MccartySep 7, 2025
Why Yamaha R-N500 Receiver does not detect USB device?
- G
  Gregory MeyerSep 7, 2025
  If your Yamaha Receiver isn't detecting the USB device, first turn off the unit, reconnect your USB device securely, and turn the unit on again. If that doesn't work, ensure the file system of the USB device is FAT16 or FAT32.
P
pmclaughlinSep 9, 2025
How to eliminate humming sound from Yamaha R-N500 Receiver?
- D
  Danielle TorresSep 9, 2025
  To eliminate a humming sound from your Yamaha Receiver, first ensure the audio plugs are firmly connected; if the problem continues, the cables may be defective. If you're using a turntable, make the GND connection between the turntable and the unit.

Yamaha R-N500 Specifications

General

Receiver type	stereo
Audio output channels	2.0 channels
Total Harmonic Distortion (THD)	0.015 %
Dynamic power per channel (4 Ohm)	150 W
Dynamic power per channel (8 Ohm)	105 W
Power output per channel (1KHz@8 Ohm)	115 W
Power output per channel (20-20KHz@8 Ohm)	80 W
HDMI in	0
Line-in	Yes
Digital audio optical in	2
Ethernet LAN (RJ-45) ports	1
Connectivity technology	Wired
Speakers connectivity type	RCA
Audio formats supported	AAC, FLAC, MP3, WAV, WMA
Video formats supported	MPEG4
Wi-Fi	-
AM band range	530 - 1710 kHz
FM band range	87.5 - 107.9 MHz
Supported radio bands	AM, FM
Preset stations quantity	40
Optical drive included	No
Sample rate	192 kHz
Product color	Silver
Damping factor	150
Volume control	Rotary
Apple docking compatibility	Not supported
Power consumption (standby)	0.1 W
Power consumption (typical)	190 W