What to do if only one speaker can be heard on the Yamaha R-N602 Receiver?
If you're only hearing sound from one speaker on your Yamaha Receiver, check the cable connections to ensure they are properly connected. If the problem persists, the cables may be defective. Also, verify that the speaker balance is set correctly using the BALANCE control.
What to do if the Yamaha R-N602 Receiver power does not turn on?
If your Yamaha Receiver doesn't power on, there could be several reasons. First, ensure the power cable is firmly connected. If the protection circuitry has been activated due to a short circuit, check that the speaker wires aren't touching each other, then try turning the power back on. If the internal microcomputer has frozen, turn the power off and then on again after at least 15 seconds. If the problem persists, disconnect the power cable from the AC wall outlet and plug it again. If the protection circuitry has been activated three times consecutively, contact your nearest Yamaha dealer or service center to request repair.
What to do if my Yamaha Receiver has no sound?
If you're not getting any sound from your Yamaha Receiver, here's what to check: First, make sure all input and output cables are correctly connected and not defective. Select the correct input source using the INPUT selector on the front panel or the remote. Ensure the SPEAKERS A/B switches are properly set. Check that your speaker connections are secure and that the mute function is off. Verify that the “Max Volume” and “Initial Volume” settings in the “Setup” menu are appropriately adjusted. Confirm that the component for the selected input source is on and playing. If using a digital audio input, ensure the connected device's audio output is set to PCM.
How to fix a Yamaha R-N602 Receiver that does not turn on?
If your Yamaha Receiver isn't powering on, there are several potential causes. First, ensure the power cable is securely connected. Also, check that the speaker wires aren't touching each other, as this could activate the protection circuitry; if this happens, turn the power off and then back on. If the issue persists, try turning the power off and on again after 15 seconds; if that doesn't work, disconnect the power cable from the AC wall outlet and plug it back in. If the protection circuitry has been activated three times consecutively, contact your nearest Yamaha dealer or service center to request repair.
What to do if firmware update via the network is failed on Yamaha R-N602?
If the firmware update via the network has failed, it may not be possible depending on the condition of the network. Update the firmware via the network again or use a USB memory device.
Why doesn't my iPod recognize the Yamaha R-N602 when using AirPlay?
If your iPod doesn't recognize the unit when using AirPlay, the unit may be connected to a multiple SSID router. Access to the unit might be restricted by the network separation function on the router. Connect the iPod to the SSID which can access the unit.
Why does the sound on my Yamaha R-N602 suddenly go off?
The sound on your Yamaha Receiver may suddenly cut off because the protection circuitry has been activated due to a short circuit. In this case, ensure that the speaker impedance matches your speakers. Another reason may be that the unit has become too hot, so ensure that the openings on the top panel are not blocked. Also, the auto power standby function may have turned the unit off. You can change the auto power standby setting in the Setup menu to turn it off.
How to fix no sound on Yamaha R-N602?
If you're not getting any sound from your Yamaha Receiver, there are several things to check. First, ensure all input and output cables are correctly connected and not defective. Then, select the appropriate input source using the INPUT selector or the remote. Make sure the SPEAKERS A/B switches are turned on, and that speaker connections are secure. Also, verify that the output hasn't been muted and that the Max Volume and Initial Volume settings in the Setup menu aren't too low. Confirm that the connected component is turned on and playing, and if using a digital audio input, ensure the audio output is set to PCM.
Why won't my Yamaha Receiver turn on?
Your Yamaha Receiver might not be turning on for several reasons. The protection circuitry may have been activated multiple times, disabling the power. In this case, the standby indicator will blink, and you should contact a Yamaha dealer for repair. Alternatively, the power cable might not be fully connected, so ensure it is firmly plugged in. A short circuit could also activate the protection circuitry; check that the speaker wires aren't touching. Finally, the internal microcomputer might have frozen due to an electrical shock or voltage drop. Try turning the power off and on again after 15 seconds, or disconnecting and reconnecting the power cable.
What to do if Yamaha R-N602 Receiver firmware update via the network failed?
If the firmware update via the network failed on your Yamaha Receiver, try updating the firmware via the network again or use a USB memory device.
General| Power Output | 80 W + 80 W (8 ohms, 20 Hz-20 kHz, 0.04% THD) |
|---|---|
| Bluetooth | Yes (SBC / AAC) |
| AirPlay | Yes |
| Type | Stereo Receiver |
| Audio Channels | 2.0 |
| Impedance | 8 ohms |
| THD | 0.04% (20 Hz-20 kHz) |
| Signal-to-Noise Ratio | 100 dB (CD) |
| DLNA | Yes |
| DAC | Burr-Brown 192 kHz/24-bit |
| AM/FM Tuner | Yes |
| Network Connectivity | Ethernet, Wi-Fi |
| Streaming Services | Spotify, Pandora, SiriusXM |
| Inputs | Optical, Coaxial, USB, RCA, Phono |
| Outputs | Headphone, Subwoofer |
| Dimensions | 435 x 151 x 392 mm |
| Weight | 9.8 kg |
| Speaker Impedance | 4 ohms |
| Supported Audio Formats | MP3, WMA, MPEG4 AAC, WAV, FLAC, AIFF, ALAC, DSD |
Detailed explanation of the buttons and indicators on the unit's front panel.
Details the buttons and their functions on the supplied remote control.
General instructions and cautions for connecting audio components and speakers.
Methods for connecting the unit to a wireless network (Wi-Fi).
How to turn on the unit, select sources, and adjust volume.
How to pair and play music from a Bluetooth-enabled device.
Guide to sharing music files from PCs/NAS and playing them back.
Instructions for playing music files from a USB storage device.
How to connect and play music from an iPod using a USB cable.
Detailed setup for network connection, IP address, DMC control, and standby.
A guide to diagnosing and resolving common problems with the unit.
To Next Page
